manualshive.com logo in svg

Chevrolet Express 2012, Owner'S Manual

Share
Download
Chevrolet Express 2012 Owner'S Manual Download Page 288

Black plate (38,1)

Chevrolet Express Owner Manual - 2012 - crc - 11/11/11

10-38

Vehicle Care

5. Remove the taillamp assembly

from the vehicle.

6. Remove the taillamp/turn signal

lamp (A) or back

‐

up lamp (B)

bulb socket by turning it
counterclockwise one quarter
turn and pulling it out of the lamp
assembly.

7. Remove the bulb by pulling it

straight out.

8. Push the new bulb into the

socket.

9. Reinstall the bulb socket by

turning it clockwise into the lamp
assembly.

10. Reverse Steps 1 through 5 to

reinstall the taillamp assembly
and applique.

Center High-Mounted
Stoplamp (CHMSL)

The Center High-Mounted Stoplamp
(CHMSL) is located above the rear
doors at the center of the vehicle.

To replace a bulb:

1. Remove the two screws from the

CHMSL assembly.

2. Remove the CHMSL assembly.

3. Turn the bulb socket

counterclockwise one quarter
turn to remove it from the lamp
assembly.

4. Pull the old bulb straight out of

the socket and push the new
bulb into the socket.

5. Turn the bulb socket clockwise

one quarter turn to install it in the
lamp assembly.

6. Reinstall the CHMSL assembly

and two screws.

Do not block or damage the CHMSL
when items are loaded on the roof
of the vehicle.

Summary of Contents for Express 2012





















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands