manualshive.com logo in svg

Chevrolet Express 2012, Owner'S Manual

Share
Download
Chevrolet Express 2012 Owner'S Manual Download Page 211

Black plate (15,1)

Chevrolet Express Owner Manual - 2012 - crc - 11/11/11

Driving and Operating

9-15

Starting and
Operating

New Vehicle Break-In

Notice:

The vehicle does not

need an elaborate break-in. But it
will perform better in the long run
if you follow these guidelines:

.

Keep the vehicle speed at
88 km/h (55 mph) or less for
the first 805 km (500 miles).

.

Do not drive at any one
constant speed, fast or slow,
for the first 805 km
(500 miles). Do not make
full-throttle starts. Avoid
downshifting to brake or
slow the vehicle.

.

Avoid making hard stops for
the first 322 km (200 miles) or
so. During this time the new
brake linings are not yet
broken in. Hard stops with
new linings can mean
premature wear and earlier
replacement. Follow this
breaking-in guideline every
time you get new brake
linings.

.

Do not tow a trailer during
break-in. See

Trailer Towing

on page 9

‑

46

for the trailer

towing capabilities of the
vehicle and more
information.

Following break

‐

in, engine speed

and load can be gradually
increased.

Ignition Positions

The ignition switch has four different
positions.

To shift out of P (Park), the ignition
must be in ON/RUN or ACC/
ACCESSORY and the regular brake
pedal applied.

A (STOPPING THE ENGINE/
LOCK/OFF):

When the vehicle is

stopped, turn the ignition switch to
LOCK/OFF to turn the engine off.

Summary of Contents for Express 2012





















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands