manualshive.com logo in svg

Chevrolet 2015 Cruze, Owner'S Manual

The Chevrolet 2015 Cruze Owner's Handbook Manual is essential for every car owner. Browse our website today to download this comprehensive manual for free, providing you with vital information on vehicle maintenance, safety, and troubleshooting. Unlock its potential by visiting manualshive.com and ensuring a seamless driving experience.

Share
Download
background image

Black plate (20,1)

Chevrolet Cruze Owner Manual (GMNA-Localizing-U.S./Canada-7707493) -

2015 - crc - 7/24/14

9-20

Driving and Operating

to the floor and holding it there
as you press the ENGINE
START/STOP button, for up to a
maximum of 15 seconds. Wait at
least 15 seconds between each
try, to allow the cranking motor
to cool down. When the engine
starts, let go of the button, and
the accelerator. If the vehicle
starts briefly but then stops
again, do the same thing. This
clears the extra gasoline from
the engine. Do not race the
engine immediately after starting
it. Operate the engine and
transmission gently until the oil
warms up and lubricates all
moving parts.

Diesel Engine Starting Procedure

The diesel engine starts differently
than a gasoline engine.

1. Turn the ignition key to ON/RUN.

If the Wait-To-Start light is
illuminated, wait until this light
goes off to start the vehicle.

2. Then turn the ignition key to

START. When the engine starts,
let go of the key.

The engine has a fast warm-up
glow plug system. The
wait-to-start light will illuminate
for a much shorter time than
most diesel engines, due to the
rapid heating of the glow plug
system.

{

Caution

If the wait-to-start light stays on
after starting the vehicle, the
vehicle may not run properly.
Have the vehicle serviced
right away.

3. If the engine does not start after

15 seconds of cranking, turn the
ignition key to LOCK/OFF. Wait
one minute for the cranking
motor to cool, then try the same
steps again.

If you are trying to start the engine
after you have run out of fuel, follow
the steps in

Running Out of Fuel

(Diesel) on page 9-60

.

When the engine is cold, let it run
for a few minutes before driving.
This lets oil pressure build up. The
engine will sound louder when
it's cold.

Cold Weather Starting (Diesel
Engine)

Use the recommended engine oil
when the outside temperature drops
below freezing. See

Engine Oil on

page 10-11

. When the outside

temperature drops below

–

18°C (0°

F), use of the engine heater is
recommended.

See

Fuel for Diesel Engines on

page 9-53

for information on what

fuel to use in cold weather.

Summary of Contents for 2015 Cruze




































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2015 Cruze

Laser 4832 Manual preview
4832
Brand: Laser Pages: 8
JASTEC von-S2 Instruction Manual preview
von-S2
Brand: JASTEC Pages: 12
Kolpin 25-9250 Owner'S And Operator'S Manual preview
25-9250
Brand: Kolpin Pages: 25
Car-Interface CI-RL4-ELINK Manual preview
CI-RL4-ELINK
Brand: Car-Interface Pages: 23
RuggON VD04 Quick Start Manual preview
VD04
Brand: RuggON Pages: 2
Doug Thorley Headers THY-464-1 Instructions preview
THY-464-1
Brand: Doug Thorley Headers Pages: 5
Edelbrock 66002 Installation Instructions preview
66002
Brand: Edelbrock Pages: 2
Volvo 1996 960 Quick Tips preview
1996 960
Brand: Volvo Pages: 10
Chevrolet Malibu 2014 Owner'S Manual preview
Malibu 2014
Brand: Chevrolet Pages: 428
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Brand: Cadillac Pages: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Brand: Fortin Pages: 9
Omix-Ada Alloy Rugged Ridge X-Clamp Manual preview
Alloy Rugged Ridge X-Clamp
Brand: Omix-Ada Pages: 2
Dodge 8W-70 Wiring Diagram preview
8W-70
Brand: Dodge Pages: 3
Weltmann KFZ-Teile 9B500016 Fitting Instructions Manual preview
9B500016
Brand: Weltmann KFZ-Teile Pages: 12
Air Lift 88365 Installation Manual preview
88365
Brand: Air Lift Pages: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Brand: Dolphin Pages: 16
Jaeger 12160509J Fitting Instructions Manual preview
12160509J
Brand: Jaeger Pages: 16
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Brand: Lexus Pages: 830

Brands by name

Popular brands

Load more brands