Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 241 / 372

background image

3. Check both sides of the dipstick, and read the lower

level. The fluid level must be in the COLD area for
a cold check or in the HOT area for a hot check.

4. If the fluid level is in the acceptable range, push the

dipstick back in all the way.

How to Add Fluid

Refer to the Maintenance Schedule to determine
what kind of transmission fluid to use. See

Recommended Fluids and Lubricants on page 6-30.

Add fluid only after checking the transmission fluid while
it is hot. (A cold check is used only as a reference.)
If the fluid level is low, add only enough of the proper
fluid to bring the level up to the HOT area for a hot
check. It doesn’t take much fluid, generally less
than 0.6 pints (0.3 L).

Don’t overfill.

Notice: We recommend you use only fluid labeled
DEXRON

®

-III, because fluid with that label is made

especially for your automatic transmission.
Damage caused by fluid other than DEXRON

®

-III

is not covered by your new vehicle warranty.

•

After adding fluid, recheck the fluid level as described
under “How to Check.”

•

When the correct fluid level is obtained, push the
dipstick back in all the way.

5-25

«
...
239
240
241
242
243
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: UnderCover Pages: 16

Brand: Taffio Pages: 8

Brand: Yescom Pages: 4

Brand: Z Automotive Pages: 16

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: Hyundai Pages: 18

Park Vision VAL632210

Brand: Valeo Pages: 25

Brand: Subaru Pages: 540

Brand: Volvo Pages: 123

Brand: Xingyun Pages: 74

Brand: Xpresskit Pages: 12

Performer-Plus 2172

Brand: Edelbrock Pages: 4

Brand: Jaeger Pages: 14

Brand: Phonocell Pages: 8

Brand: Subaru Pages: 2

Brand: Edelbrock Pages: 2

Brand: Hudson Pages: 77

TRUCK 2500 2017

Brand: RAM Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands