manualshive.com logo in svg

Chevrolet 2003 tracker, Owner'S Manual

The Chevrolet 2003 Tracker manual is available for free download on our website. This comprehensive user manual offers detailed instructions and valuable information on operating and maintaining your Chevrolet Tracker. Download it today from manualshive.com to enhance your driving experience and ensure optimal vehicle performance.

Share
Download
background image

When to Inspect the Engine Air
Cleaner/Filter

Inspect the air cleaner/filter every 15,000 miles
(25 000 km) and replace every 30,000 miles
(50 000 km). If you are driving in dusty/dirty conditions,
inspect the filter at each engine oil change.

How to Inspect the Engine Air
Cleaner/Filter

To inspect the air cleaner/filter remove the filter from
the vehicle and lightly shake the filter to release
loose dust and dirt. If the filter remains caked with dirt,
a new filter is required.

To inspect or replace the filter, do the following:

1. Release the four clips

on the cover.

2. Lift the cover up.

5-21

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

JAC S5 Workshop Manual preview
S5
Brand: JAC Pages: 70
N-Com B3 User Instructions And Safety preview
B3
Brand: N-Com Pages: 28
RaceChip Pro 2 Installation Manual preview
Pro 2
Brand: RaceChip Pages: 12
Kia 2016 Cadenza Owner'S Manual preview
2016 Cadenza
Brand: Kia Pages: 419
Roadmaster Sterling ALL-TERRAIN 576 Owner'S Manual & Installation Instructions preview
Sterling ALL-TERRAIN 576
Brand: Roadmaster Pages: 12
Buick 2005 Terraza Owner'S Manual preview
2005 Terraza
Brand: Buick Pages: 428
Victory 4x4 UNI-UPRS Install Instructions Manual preview
UNI-UPRS
Brand: Victory 4x4 Pages: 13
Ironton 44596 Owner'S Manual preview
44596
Brand: Ironton Pages: 7
BESAFE iZi Flex Manual preview
iZi Flex
Brand: BESAFE Pages: 4
RAM 2011 DAKOTA User Manual preview
2011 DAKOTA
Brand: RAM Pages: 76
Advantech TREK-550 Manual preview
TREK-550
Brand: Advantech Pages: 59
PAC Stinger ELEV8 Install Manual preview
Stinger ELEV8
Brand: PAC Pages: 14
Kolpin 98310 Product Instructions preview
98310
Brand: Kolpin Pages: 3
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Brand: Cadillac Pages: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Brand: Fortin Pages: 9
Safe Fleet RVS systems RVS-M641 Instruction Manual preview
RVS systems RVS-M641
Brand: Safe Fleet Pages: 24
RHOX LGT-381L Installation Instructions Manual preview
LGT-381L
Brand: RHOX Pages: 8
Cadillac STS 2011 Owner'S Manual preview
STS 2011
Brand: Cadillac Pages: 529

Brands by name

Popular brands

Load more brands