Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 147 / 372

background image

•

Sometimes when the engine is idling at a stop, the
light may blink on and off. This is normal.

•

If you make a hard stop, the light may come on for
a moment. This is normal.

{

CAUTION:

Do not keep driving if the oil pressure is low.
If you do, your engine can become so hot that
it catches fire. You or others could be burned.
Check your oil as soon as possible and have
your vehicle serviced.

Notice: Damage to your engine from neglected oil
problems can be costly and is not covered by
your warranty.

Overdrive Off Light

This light comes on when
the automatic four-speed
transmission, if equipped,
has been converted to the
three-speed mode and the
overdrive is turned off.

This light also comes on as a check for about five
seconds when the ignition key is turned to ON or
START.

Four-Wheel-Drive Light

If you have four-wheel
drive, this light comes on
when the ignition switch
is on and the transfer case
lever is in one of the
four-wheel drive positions.

See

Four-Wheel Drive on page 5-53.

3-35

«
...
145
146
147
148
149
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: cam Pages: 2

Brand: Dapper Lighting Pages: 2

Brand: JAC Pages: 70

BLACK STEEL S2560

Brand: Fab Fours Pages: 9

Brand: BrandMotion Pages: 8

Brand: Ironton Pages: 7

Brand: Ford Pages: 2

Brand: Renault Pages: 238

Brand: Whispbar Pages: 15

Brand: Westin Pages: 3

2917 Nstallation

Brand: Edelbrock Pages: 1

Brand: RAM Pages: 330

Brand: Velleman Pages: 17

Brand: Jeep Pages: 52

2013 Accord Sedan

Brand: Honda Pages: 26

Brand: Jeep Pages: 440

Juice Pack Reserve

Brand: Mophie Pages: 2

Brand: TrailFX Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands