Chevrolet 2003 tracker Owner'S Manual Download | Manualshive

Page: 136 / 372

background image

Warning Lights, Gages and
Indicators

This part describes the warning lights and gages that
may be on your vehicle. The pictures will help you
locate them.

Warning lights and gages can signal that something is
wrong before it becomes serious enough to cause
an expensive repair or replacement. Paying attention
to your warning lights and gages could also save you or
others from injury.

Warning lights come on when there may be or is a
problem with one of your vehicle’s functions. As you
will see in the details on the next few pages, some
warning lights come on briefly when you start the engine
just to let you know they’re working. If you are familiar
with this section, you should not be alarmed when
this happens.

Gages can indicate when there may be or is a problem
with one of your vehicle’s functions. Often gages
and warning lights work together to let you know when
there’s a problem with your vehicle.

When one of the warning lights comes on and stays on
when you are driving, or when one of the gages
shows there may be a problem, check the section
that tells you what to do about it. Please follow this
manual’s advice. Waiting to do repairs can be
costly – and even dangerous. So please get to know
your warning lights and gages. They’re a big help.

3-24

«
...
134
135
136
137
138
...
»

Summary of Contents for 2003 tracker





















































































































































































































































































































































































Reviews:

No comments

Related manuals for 2003 tracker

Brand: Samsung Pages: 133

Brand: Toyota Pages: 35

Brand: Trailboss Pages: 8

Brand: Chevrolet Pages: 2

adaptiv mini ADVM-BM1

Brand: Connects2 Pages: 4

Brand: Joie Pages: 53

Brand: GReddy Pages: 12

Brand: S&B Filters Pages: 4

Brand: Mazda Pages: 3

Brand: Mont Blanc Pages: 2

Brand: Butts of Bawtry Pages: 2

LineCast Auto FM

Brand: Belkin Pages: 15

Brand: Rover Pages: 285

Brand: Xpresskit Pages: 12

Brand: Subaru Pages: 399

Brand: Buick Pages: 112

Brand: PEUGEOT Pages: 404

QuadraTop Adventure Top S

Brand: Quadratec Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands