manualshive.com logo in svg

CHERUBINI A510078, Instructions Manual, Page: 18 / 22

Share
Download
CHERUBINI A510078 Instructions Manual Download Page 18

18

Parameter 

Number

Size

Parameter 

Name

Default 

Value

Description

22

4

MIN_

LEVEL_

TIME

100

Time to reach Min level starting from the 
Max Level.
Defines the time thousandth of a second 
necessary to reach the complete close 
position starting from complete open 
position.

 Parameters Values                                        Min: 100                  Max: 100.000

Value

Description

100-100.000 Time expressed in thousandths of a second

Parameter 

Number

Size

Parameter 

Name

Default 

Value

Description

23

4

INVERTION_ 

TIMEOUT

1000

Time in thousandth of a second after 
which the movement direction can be 
changed.

 Parameters Values                                        Min: 1000                  Max: 10.000

Value

Description

1000-10.000 Time expressed in thousandths of a second

Parameter 

Number

Size

Parameter 

Name

Default 

Value

Description

24

4

LIMIT_ 

SWITCH_ 
TIMEOUT

3000

Time in thousandth of a second for  
recognizing that the limit switch has 
been reached.

 Parameters Values                                        Min: 1000                  Max: 10.000

Value

Description

1000-10.000 Time expressed in thousandths of a second

E

NG

L

IS

H

Summary of Contents for A510078























Reviews:

No comments