manualshive.com logo in svg

CHERUBINI A510078, Instructions Manual, Page: 17 / 22

Share
Download
CHERUBINI A510078 Instructions Manual Download Page 17

17

Calibration

Defines the status of the calibration procedure. By default, the calibration starts in 
automatic mode as soon as a movement command has been set by external switch or 
by Z-Wave™ network.
Afterwards the calibration can be done again by setting this parameter to 20 to 0 or 
using the offline setup mode.
The calibration procedure can be made manually by setting the time needed to 
complete a full movement from complete close to complete open and vice versa. The 
procedure can be carried on by setting parameter 20 to 1 and parameter 21 and 22, to 
the appropriate time in millisecond.
During the calibration, the LED indicator blinks repeatedly in BLUE.

Parameter 

Number

Size

Parameter 

Name

Default 

Value

Description

20

1

CALIBRA-

TION_COM-

PLETE

0

Define if the device has been calibrated.

 Parameters Values                                        Min: 0                        Max: 1

Value

Description

0

TO_BE_DONE (Calibration to be done)

1

DONE (Calibration has been done)

Parameter 

Number

Size

Parameter 

Name

Default 

Value

Description

21

4

MAX_ 

LEVEL_

TIME

100

Time to reach Max level starting from 
the Min Level.
Defines the time in thousandth of a se-
cond necessary to reach the complete 
open position starting from complete 
close position.

 Parameters Values                                        Min: 100                   Max: 100.000

Value

Description

100-100.000 Time expressed in thousandths of a second

E

NG

L

IS

H

Summary of Contents for A510078























Reviews:

No comments