manualshive.com logo in svg

CHERUBINI A510078, Instructions Manual, Page: 16 / 22

Share
Download
CHERUBINI A510078 Instructions Manual Download Page 16

16

CONFIGURATIONS

Favorite positions

Parameter 

Number

Size

Parameter 

Name

Default 

Value

Description

2

1

ON_ 

FAVORITE_ 

LEVEL

80

The On level reached when the Up 
Button received a double click.

 Parameters Values                                         Min: 50                        Max: 99

Value

Description

50-99

50-99% opening level (99% correspond to completely open)

Parameter 

Number

Size

Parameter 

Name

Default 

Value

Description

3

1

ON_ 

FAVORITE_ 

LEVEL

20

The Off level reached when the Down 
Button received a double click. 

 Parameters Values                                        Min: 0                        Max: 49

Value

Description

0-49

0-49% opening level (0 correspond to completely closed)

The system can set two favorite positions: one for the upward movements (opening 
movements) 

Favorite level for ON position

, the other for the downward movements 

(closing movements) 

Favorite level for OFF position

.

E

NG

L

IS

H

Summary of Contents for A510078























Reviews:

No comments