CHEELCARE Companion User Manual Download Page 30

Page: 30 / 33

V1.1, May 12, 2020

Companion User Manual

P a g e

Maintenance schedule

Task

How

Often?

How?

Clean Companion
exterior

Monthly

Clean using a soft cloth dipped in soap and water: avoid
hoses and pressure washers.

Check wheel

Weekly

Clean dirt from the wheel and check wheel tread.

Check brake pad
wear

Every 6

Months

Check for effective braking by squeezing the brake
lever. Have an authorised service provider to service or
replace brake pads.

Professional
Companion
inspection

Yearly

Have an authorised professional service provider to
service the device.

Replace tires

necessary

Have an authorised professional service provider to
replace the tires.

Check fastening
screws

Weekly

Inspect fasteners visually for any damage. Check that
all connections are tightened properly.

Troubleshooting Guide

The Companion Unit is not powering ON:

•

Make sure that you turned ON the power with your key and pressed the red power

button on the handlebar.

•

Ensure that the battery is fully charged (charger indicates a GREEN light).

The front wheel slips

–

spins in place:

•

The front wheel is too far from your wheelchair. Adjust the Companion Unit so that the

front wheel is as close as possible to the footrest. The Power Unit should be almost
vertical when the Companion is attached to your wheelchair.

•

When driving uphill, lean forward in your wheelchair to shift your center of gravity

forward.

•

Check the tire thread; replace if too worn out. Always start slow, in Speed Mode 1.

Summary of Contents for Companion

































Search results

Summary of Contents for Companion

Reviews:

Brands by name

Popular brands

CHEELCARE Companion, User Manual

Search results

Summary of Contents for Companion

Reviews:

Brands by name

Popular brands