Charles Fiber Pedlock BDO2 Series General Description And Installation Download

Page: 22 / 22

LT-BDO20X-801

Page 22 of 22

Printing

TECHNICAL ASSISTANCE AND REPAIR SERVICE

For questions on product repair or if technical assistance is required, contact Charles Technical Support.

847-806-8500

[email protected]

(email)

http://www.charlesindustries.com/techserv.htm

SPECIFICATIONS

5.1.

Physical Specifications

Feature

BDO203

BDO204

BDO205

Height, overall

42.75 in.

45 in.

Height, base only, incl. collar

18 in.

Height, dome only

28.5 in.

30 in.

Height, dome only, extended version *

35 in.

34 in.

Height, base bottom to ground line

8.5 in.

8.5 in

Height, dome top to ground line

34.25 in.

34.25 in

36.5 in

Height, dome top to ground line, extended version *

41.5 in.

41.5 in

40.5 in

Depth, base (front to back)

9.75 in.

10.8 in.

12.75 in.

Width, base (side to side)

10.25 in.

11.75 in.

12.75 in.

Diameter, base collar, O.D. (Outside Diameter)

6.6 in.

8.1 in.

10.75 in.

Diameter, base collar, I.D. (Inside Diameter)

6.2 in.

7.7 in.

10.25 in.

Diameter, dome, O.D. (not the cap)

7.1 in.

8.6 in.

11.25 in.

Diameter, dome, I.D.

6.7 in.

8.2 in.

10.88 in.

Weight

18 lbs.

21 lbs.

29 lbs.

* Part numbers BDO203-EXX, BDO204-EXX, and BDO205-EXX have a top bulkhead area.

5.2.

Ordering Information

Part Number

Description

97-SCU12LF3M

Loose tube fiber fanout w/ 12 SC/UPC connectors, 3 m. long

97-SCU12RF3M

Ribbon fiber fanout w/ 12 SC/UPC connectors, 3 m. long

97-SCA12LF3M

Loose tube fiber fanout w/ 12 SC/APC connectors, 3 m. long

97-SCA12RF3M

Ribbon fiber fanout w/ 12 SC/APC connectors, 3 m. long

97-FIBR24TRAY

Splice tray kit, with one 12/24 Fiber tray

UMS36-STD

36” universal metal mounting-stake, galvanized, with hardware to attach the BDO

base to the stake.

UMS42-STD

Same as above, but 42” long.

UMB102A

24” universal metal pole-mount bracket, galvanized, with mounting hardware to

attach the base to the bracket.

97-RIBNTUBEKIT

3M® ribbon transportation tube kit, 3 ft., 10 each.

97-RIBNCLIPKIT

(for BDO203)

Ribbon saddle clip kit, holds up to 144 fibers, 40 ea.

97-RIBNCLIPLG

(for BDO204 & BDO205)

Ribbon saddle clip kit, large, holds up to 288 fibers, 40 ea.

Summary of Contents for Fiber Pedlock BDO2 Series























Search results

Summary of Contents for Fiber Pedlock BDO2 Series

Reviews:

Related manuals for Fiber Pedlock BDO2 Series

Brands by name

Popular brands

Charles Fiber Pedlock BDO2 Series, General Description And Installation

Search results

Summary of Contents for Fiber Pedlock BDO2 Series

Reviews:

Related manuals for Fiber Pedlock BDO2 Series

Brands by name

Popular brands