background image

100458 - 1200W PORTAbLE GENERATOR

TROUbLESHOOTING

28

TROUbLESHOOTING

Problem

Cause

Solution

Generator will not start.

No fuel.

Add fuel.

Faulty spark plug.

Replace spark plug.

Unit loaded during start up.

Remove load from unit.

Generator will not start;

Generator starts but runs roughly.

Low oil level.

Fill crankcase to the proper level.
Place generator on a flat, level surface.

Choke in the wrong position.

Adjust choke.

Spark plug wire loose.

Attach wire to spark plug.

Generator shuts down during operation.

Out of fuel.

Fill fuel tank.

Low oil level.

Fill crankcase to the proper level. Place 
generator on a flat, level surface.

Generator cannot supply enough power 
or overheating.

Generator is overloaded.

Review load and adjust. See “Connecting 
Electrical Loads.”

Insufficient ventilation.

Check for air restriction. Move to a well 
ventilated area.

No AC output.

Cable not properly connected.

Check all connections.

Connected device is defective.

Replace defective device.

Circuit breaker is open.

Reset circuit breaker

Loose wiring.

Inspect and tighten wiring connections.

Other.

Contact the help line.

Generator gallops.

Engine governor defective.

Contact the help line.

Repeated circuit breaker tripping.

Overload.

Review load and adjust. See "Connecting 
Electrical Loads."

Faulty cords or device.

Check for damaged, bare or frayed wires. 
Replace defective device.

For further technical support:

Technical Support Team 
Mon-Fri 8:30 AM-5:00 PM (PST/PDT) 
Toll Free 1-877-338-0999 
[email protected]

Summary of Contents for 100458

































Reviews: