background image

100402 - 2000W DUAL FUEL INVERTER GENERATOR

IMPORTANT SAFETY INSTRUCTIONS

4

IMPORTANT SAFETY INSTRUCTIONS

 

WARNING

Cancer and Reproductive Harm – www.P65Warnings.ca.gov

 

DANGER

Generator exhaust contains carbon monoxide, a colorless, 
odorless, poison gas. Breathing carbon monoxide will cause 
nausea, dizziness, fainting or death. If you start to feel dizzy 
or weak, get to fresh air immediately.

OPERATE GENERATOR OUTDOORS ONLY IN A WELL 
VENTILATED AREA.

DO NOT operate the generator inside any building, including 
garages, basements, crawlspaces and sheds, enclosure or 
compartment, including the generator compartment of a 
recreational vehicle.

DO NOT allow exhaust fumes to enter a confined area 
through windows, doors, vents or other openings.

 

DANGER

Using a generator indoors 

CAN KILL YOU IN MINUTES

Generator exhaust contains carbon monoxide. This is a 
poison you cannot see or smell.

NEVER

 use inside a home or garage, 

EVEN IF

 doors and 

windows are open.

ONLY

 use 

OUTSIDE

 and far away from windows, doors, 

and vents.

Install battery-operated carbon monoxide alarms or plug-in 
carbon monoxide alarms with battery back-up according to 
the manufacturer’s instructions.

 

DANGER

Rotating parts can entangle hands, feet, hair, clothing and/
or accessories. Traumatic amputation or severe laceration 
can result.

Keep hands and feet away from rotating parts.

Tie up long hair and remove jewelry.

Operate equipment with guards in place.

DO NOT wear loose-fitting clothing, dangling drawstrings or 
items that could become caught.

 

WARNING

Operation of this equipment may create sparks that can 
start fires around dry vegetation.

A spark arrestor may be required. The operator should 
contact local fire agencies for laws or regulations relating to 
fire prevention requirements.

 

DANGER

Generator produces powerful voltage.

DO NOT touch bare wires or receptacles.

DO NOT use electrical cords that are worn, damaged or 
frayed. Use Champion electrical cords only for proper 
application.

DO NOT operate generator in wet weather.

DO NOT allow children or unqualified persons to operate or 
service the generator

Use a ground fault circuit interrupter (GFCI) in damp areas 
and areas containing conductive material such as metal 
decking.

Connection to your home’s electrical system requires a 
listed 30A transfer switch installed by a licensed electrician 
and approved by the local authority having jurisdiction.  The 
connection must isolate the generator from the utility power 
and must comply with all applicable laws and electrical 
codes.

 

WARNING

Sparks can result in fire or electrical shock.

When servicing the generator:

Disconnect the spark plug wire and place it where it cannot 
contact the plug or any other metal object.

DO NOT check for spark with the plug removed.

Use only approved spark plug testers.

Summary of Contents for 100402


































Reviews: