background image

CONTENTS

Preparation .............................. 1-4
Assembly ................................. 5-9

Installation ............................ 10-19
Install the Door Control ............. 20-21

Install the Protector System

®

 ...... 22-25

Power  .................................. 26-27

Adjustments .......................... 28-30

Operation.................................. 31

Features ................................... 32

Door Control .......................... 33-34

Remote Control ...................... 34-35

To Erase the Memory .................... 35

To Open the Door Manually ............ 36

Maintenance .............................. 37

Troubleshooting ...................... 38-39

Accessories ............................... 40

Repair Parts 

1/2 hp Belt Drive 

Garage Door Opener

Please read this manual and the enclosed safety materials carefully!

Fasten the manual near the garage door after installation.

 The door WILL NOT CLOSE unless the Protector System

®

 is connected and

properly aligned.

Periodic checks of the garage door opener are required to ensure safe operation.

 The model number label is located on the left side panel of your garage

door opener.

This garage door opener is compatible with MyQ

®

 and S 2.0

®

 accessories.

  DO NOT install on a one-piece door if using devices or features providing unattended

close. Unattended devices and features are to be used ONLY with sectional doors.

Models

• 

WD832KEV

• 

WD832KEVG

FOR RESIDENTIAL USE ONLY 

..

Summary of Contents for WD832KEV












































Reviews: