background image

    90108A036  

¾ USS Flat Washer   

 

 

 

 

    97801A104  

1/8 x 2 Lg. Nail 

 

 

 

 

 

    98410A128  

0.750 Dia. Retainer Ring 

 

 

 

 

10 

 

 

 

 

ALIF-412-012 

Packing 

Pin 

      4 

    

C1100-112-4500M

  1.10 O.D.  x 4 ½” Safety Latch Spring 

 

 

4  

    ALRK-412-002-XX

 

Cross 

Rail 

Weldm’t. 

     2 

    GL-12-055   

2.25 Dia. Pulley 

 

 

 

 

 

    GL-12-057   

Cross Rail Chain Connector   

 

 

 

    GL-12-078   

Safety Stop Plate 

 

 

 

 

 

 

 

 

 

GL-12-089-XX 

Safety 

Latch 

      4 

    GL-12-098   

Safety Latch / Bearing Pin 

 

 

 

 

    GL-12-099   

Safety Latch Pin 

 

 

 

 

 

    ALRK-412-094

 

BL634, 271 Pitch Male Ends, Cross Rail Chain 

 

PKG 

    91259A587  

0.313 Dia. 1.50 Lg. Shoulder Bolt 

 

 

 

HK 

    90640A129  

¼-20UNC Nylon Lock Nut   

 

 

 

HK 

 

 

 
 
*** Note: All hardware unless specified is grade 2. All hardware is 
zinc coated unless specified. Parts with PKG at the end are packed on 
the lift and parts with HK at the end are packaged in a box and put on 
the lift. 

 

13

Summary of Contents for 44012LR



























Reviews: