manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 72

 

 

 

MAY 2019 

 

2. Status Indicator RAPs

 

2-60 

CMT-130TC Book Trimmer 

RAP 2.52 Elevator Door Interlocks 

Elevator I/O PWB Inputs 3, 6, and 12 

The Elevator and Tilt Conveyor have a total of 
three access doors that have interlock switches.  
Opening any one of these doors will stop all 
movement in the trimmer and its accessories. 

Possible Fault Indicators 

 

“Elevator Tilt Door Open”, 
“Elevator Door Open”

, or 

“Eleva-

tor Top Door Open”

 message is 

displayed while all doors are closed. 

 

A door is open, but the Elevator and 
trimmer continue to operate. 

 

A door is open, but no message is dis-
played on the screen. 

Initial Actions 

Check that all cables between the trimmer, Ele-
vator, and Tilt Infeed Conveyor are securely fas-
tened and are not damaged. 

Check that all three doors are securely closed.   

Check and repair loose or damaged wires 43, 
49, 57 at the 

Elevator’s electrical panel.  Check 

and repair loose or damaged wires on all 3 door 
interlock switches. 

Procedure (does not operate with doors 
closed) 

1.  Does the screen show an 

“Elevator door 

open” message? 

Y  N 

Cycle power OFF and then back ON.  Then 
go to the diagnostic screen (GP 6.2 In-
put/Output Diagnostics). Open each door.  Is 
a tone heard with each opening? 

Y  N 

Disconnect power and replace the Ele-
vator I/O PWB (REP 4.26 Accessory 
PWB Replacement). 

Disconnect power and replace the defective 
interlock switch (PL 5.33 Elevator 
56421TCA (6/7), PL 5.34 Elevator 
56421TCA (7/7), or PL 5.45 Tilt Conveyor 
56600TCA (7/8)). 

2.  Check the operation of the indicated inter-

lock switch.  For Elevator interlocks, make 
sure that the actuator key engages fully into 
the switch body when the door is closed, 
and pulls out of the switch body when the 
door is opened.  For the Tilt Conveyor inter-
lock, make sure that both actuators are not 
depressed when the door is closed, and are 
depressed when the door is open.  Adjust if 
necessary (GP 6.11 Keyed Interlock 
Switches or GP 6.10 Micro-Switches).  Did 
this fix the problem? 

Y  N 

Perform RAP 2.11 Interlock Test and re-
place any defective switches. 

Repair complete. 

Procedure (operates with a door open) 

WARNING 

Do not operate the machine until this switch 
is replaced and functioning properly.  Failure 
to do so could allow the machine to operate 
in an un-safe state.  Serious injury or death 
may result. 

1.  Check the operation of the applicable inter-

lock switch.  For Elevator interlocks, make 
sure that the actuator key engages fully into 
the switch body when the door is closed, 
and pulls out of the switch body when the 

door is opened.  For the Tilt Conveyor inter-
lock, make sure that both actuators are not 
depressed when the door is closed, and are 
depressed when the door is open.  Adjust if 
necessary (GP 6.11 Keyed Interlock 
Switches or GP 6.10 Micro-Switches).  Did 
this fix the problem? 

Y  N 

Perform RAP 2.11 Interlock Test and re-
place any defective switches. 

Repair complete. 

 

 

 

Figure 2-79. Elevator Door Interlocks 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands