manualshive.com logo in svg

Challenge 130TC-A-160000, Service Manual

Share
Download
Challenge 130TC-A-160000 Service Manual Download Page 235

 

 

 

 

MAY 2019 

 

CMT-130TC Book Trimmer

 

6-21 

6. General Procedures/Information

 

GP 6.18 Scheduled Maintenance 

Regular maintenance extends the life of the trim-
mer.  Maintenance tasks are broken down into 
weekly, semi-annual, and annual. 

Weekly Procedure 

WARNING 

Disconnect and lockout power as described 
in the Power Lockout Procedure on page ix. 

Clean: 

Do not use petroleum or acid-based 
cleaners or solvents to clean the console 
or any part of the trimmer and accesso-
ries.  Doing so may result in permanent 
damage.

 

1.  Clean the console using a mild, non-abra-

sive soap and water solution and a moist 
cloth. 

2.  Clean the machine exterior and accessory 

exteriors using a mild, non-abrasive soap 
and water solution and a moist cloth. 

3.  Clean paper dust and paper scrap from the 

inside of the machine using a vacuum. 

4.  Clean the 

trimmer’s table surfaces, Elevator 

shelves, and conveyor belts using a mild, 
non-abrasive soap and water solution and a 
moist cloth. 

5.  Remove the lower front door panel. 

6.  Clean the hydraulic valves, hoses, fittings, 

and manifold using a mild, non-abrasive 
soap and water solution and a moist cloth. 

7.  Clean the fan covers using a dry cloth. 

8.  Clean paper dust and paper scrap from the 

area underneath the table. 

9.  Go to Section RAP 2.80 Final Actions/Sys-

tem Checks if closing the service call. 

Semi-Annual Procedure 

1.  Perform ADJ 4.4 Lubrication. 

2.  Perform ADJ 4.5 Accuracy Adjustment. 

3.  Perform ADJ 4.8 Timing and Conveyor Belt . 

4.  Perform the Weekly Procedure. 

5.  Reinstall all covers. 

6.  Place the trimmer and accessory equipment 

into its normal operating position according 
to the Installation and Operator's Manual. 

7.  Perform the System Safety Check found in 

the Installation and Operator's Manual. 

8.  Go to Section RAP 2.80 Final Actions/Sys-

tem Checks if closing the service call. 

Annual Procedure 

1.  Perform REP 4.11 Oil / Filter Change. 

2.  Perform REP 4.12 Air Filter Change. 

3.  Perform the Semi-Annual Procedure. 

4.  Go to Section RAP 2.80 Final Actions/Sys-

tem Checks if closing the service call. 

 

Summary of Contents for 130TC-A-160000



























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands