background image

16 

 

 

Fig.15 Heater 

 

4.6 Power Board 

In  case  of  the  failure  to  start,  charge  or  the  flashing  of  charge  indicator,  the  power  board  may  be 
damaged. If the instrument fails to start, first check whether the cables of control board X1 and power 
board X3 are plugged in. If they are plugged in, remove 4 screws on the bottom of instrument (as shown 
in  Fig.16)  and  gently  pull  out  the  base  of  instrument  with  care  not  to  damage  the  cable  X2,  pull  out 
cables  X2  and  X3,  measure  whether  there  is  12.6V  output  at  pins  1  and  4  of  cable  X3  (as  shown  in 
Fig.17); if so, the power module is not damaged; if not, the power module is damaged, and proceed to 
the  determination  whether  the  power  board  or  battery  is  damaged.  If  the  power  board  is  damaged, 
remove the screws on the power board to replace the power board. 

The charge failure may be caused by the damage of battery or power board. To find out the cause, insert 
the  good-working  battery  which is  fully  charged into  the  instrument,  start  the  system  and  observe  the 
battery icon at the upper right corner of screen, and if no lightning symbol is shown on the icon, it means 
that  the  power  board  is  damaged;  or  measure  the  voltage  on  both  sides  of  R9  on  the  back  of  power 
board, and if there is no charge voltage (less than 0.1V), the power board is damaged. 

 

Fixing screws of 
heater 

Summary of Contents for 6481 Series





























Reviews: