CET iMeter 6, User Manual

Page: 111 / 125

CET Electric Technology
104
“Execute” command is received without first having received an “Arm” command, the meter ignores the “Execute”
command and returns the 0x04 exception code.
Register Property Description Format Note
9100 WO Arm DO1 Close UINT16
Writing “0xFF00” to
the register to perform
the described action.
9101 WO Execute DO1 Close UINT16
9102 WO Arm DO1 Open UINT16
9103 WO Execute DO1 Open UINT16
9104 WO Arm DO2 Close UINT16
9105 WO Execute DO2 Close UINT16
9106 WO Arm DO2 Open UINT16
9107 WO Execute DO2 Open UINT16
9108 WO Arm DO3 Close UINT16
9109 WO Execute DO3 Close UINT16
9110 WO Arm DO3 Open UINT16
9111 WO Execute DO3 Open UINT16
Table 5-60 DO Control
5.10.9 Clear/Reset Control
Register Property Description Format Note
6400 WO Manual WFR Log #1 Trigger UINT16
Writing “0xFF00” to
the register to execute
the described action.
6401 WO Manual WFR Log #2 Trigger UINT16
6402 WO Clear DR #1 (High-Speed) UINT16
6403 WO Clear DR #2 (High-Speed) UINT16
6404 WO Clear DR #3 (High-Speed) UINT16
6405 WO Clear DR #4 (High-Speed) UINT16
6406 WO Clear DR #5 (Standard) UINT16
… WO … UINT16
6416 WO Clear DR #15 (Standard) UINT16
6417 WO Clear DR #16 (Standard) UINT16
6418 WO Clear WFR Log #1 UINT16
6419 WO Clear WFR Log #2 UINT16
6420 WO Clear IER Log UINT16
6421 WO Clear PQ Log UINT16
6422 WO Clear SOE Log UINT16
6423 WO Clear All Energy
1)
UINT16
6424 WO Clear Max./Min. Log of This Month UINT16
6425 WO Clear Peak Demand Log of This Month UINT16
6426 WO Clear Counter #1 (DI1) UINT16
6427 WO Clear Counter #2 (DI2) UINT16
… WO … UINT16
6430 WO Clear Counter #5 (DI5) UINT16
6431 WO Clear Counter #6 (DI6) UINT16
6432 WO Clear Device Operating Time UINT16
6433 WO Manual Switch TOU Schedule UINT16
6434 WO Clear TOU Energy UINT16
6435 WO Send Testing Email UINT16
6436 WO Clear Event Counter UINT16
6437 WO Clear all Data
2)
UINT16
Writing “0xFF00” to
the register clears all of
the above
Table 5-61 Clear/Reset Registers
Notes:
1) Writing “0XFF00” to the register clears all 3-Phase, Total Energy Measurement, TOU Energy and Interval Energy Measurements.
2) Writing “0XFF00” to the register clears all logs, including Data Recorder, Waveform Recorder, Energy Log, PQ Log, SOE Log, Max./Min.
Log of This Month (Since Last Reset), Peak Demand of This Month (Since Last Reset), DI Counters, Energy Registers, Device Operating
Time and TOU energy.
5.11 Time
There are two sets of Time registers supported by the iMeter 6 – Year / Month / Day / Hour / Minute / Second
(Registers # 60000 to 60002) and UNIX Time (Register # 60004). When sending time to the iMeter 6 over Modbus
communications, care should be taken to only write one of the two Time register sets. All registers within a Time
register set must be written in a single transaction. If registers 60000 to 60004 are being written to at the same
time, both Time register sets will be updated to reflect the new time specified in the UNIX Time register set
(60004) and the time specified in registers 60000-60002 will be ignored. Writing to the Millisecond register