manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 69

 

 

3.10 Associated Clients 

The administrator can obtain detailed wireless information and all associated clients status via this 

page. Please click on Wireless -> Associated Clients. The the Associated Clients Status appears. 

 

Wireless Information

 : Display the Virtual AP configuration information of the system. 

 

VAP

 : Display number of system's Virtual AP. 

 

ESSID

 : Extended Service Set ID of the Virtual AP. 

 

Status

 : Display Virtual AP status currently. 

 

Security Type : 

Security type activated by the Virtual AP. 

 

Clients : 

Number of clients currently associated to the Virtual AP. 

 

 

 

4.  WDS Mode Configuration

 

When WDS mode is chosen, the system can be configured as an WDS mode. This section provides 

detailed explanation for users to configure in the WDS mode with help of illustrations. In the WDS 

mode, functions listed in the table below are also available from the Web-based GUI interface. 

4.1 Chose Your Operating Mode ( WDS Mode ) 

The system administrator can set the desired mode via this page, and then configure the system 

according to their deployment needs, Please click on 

System -> Operating

 Mode and follow the 

below setting. 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands