manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 33

 

 

2.6 Configure Wireless Advanced Setup 

The administrator can change the Slot Time, ACK Timeout, RTS threshold and fragmentation 

threshold settings for the system. Please click on 

Wireless -> Advanced Setup

 and follow the 

below setting.

 

 

 

Slot Time : 

Slot time is in the range of 

9~1489

 and set in unit of 

microsecond

. The default 

value is 

9

 microsecond.

 

Slot time is the amount of time a device waits after a collision before retransmitting a 

packet. Reducing the slot time decreases the overall back-off, which increases 

throughput. Back-off, which is a multiple of the slot time, is the random length of time a 

station waits before sending a packet on the LAN. For a sender and receiver own right of 

the channel the shorter slot time help manage shorter wait time to re-transmit from 

collision because of hidden wireless clients or other causes. When collision sources can 

be removed sooner and other senders attempting to send are listening the 

channel(CSMA/CA) the owner of the channel should continue ownership and finish their 

transmission and release the channel. Then, following ownership of the channel will be 

sooner for the new pair due to shorter slot time. However, when long duration of existing 

collision sources and shorter slot time exist the owners might experience subsequent 

collisions. When adjustment to longer slot time can’t improve performance then RTS/CTS 

could supplement and help improve performance. 

 

 

 

 

 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands