manualshive.com logo in svg

Cerio DT-300N, User Manual

Share
Download
Cerio DT-300N User Manual Download Page 18

 

 

1.8   Wizard Setup 

The setup wizard is designed to be an 'easy to use' utility that allows quick modification of the 

DT-300N

 UI Web-based GUI interface settings . The wizard should take no longer than 5 minutes 

to use. Please be aware that the wizard doesn't give full access to all the setup options in 

DT-300N

 

in/Outdoor PoE Bridge Router AP.   

 

This is purely because the wizard has been designed for a quick and easy setup aimed at all users. 

More advanced users can configure the remaining settings using the advanced settings options 

from the setup menu. 

 

 

 

Chose Your Operating Mode 

DT-300N 

supports six operational modes, 

AP and AP+WDS mode

, 

WDS mode

, 

Client  

Repeater AP

 

mode

,

 WISP

 

and

 

WISP + Repeater AP mode etc.

 respectively with built-in remote 

management features 

 

 

 

Wizard Guide 

Please click on 

System 

 Setup Wizard

 

 Next and follow the below guide. 

 

 

Summary of Contents for DT-300N





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands