12 I 097 U
CMB2 Cutting JAWS
OPERAtiOn & PARtS inStRuCtiOn MAnuAL
12 I 097 U
CMB2 Cutting JAWS
OPERAtiOn & PARtS inStRuCtiOn MAnuAL
WARning
Read and understand this instruction before using
this cutting jaws.
A person who has not read and does not understand
all operating instructions is not qualified to operate
these jaws. Failure to read and understand safety
instructions may result in injury or death.
Electrical Shock Hazard: The tool is not insulated and
the jaws will conduct electricity. This product should
be used only by persons knowledgeable in the safe
use of these jaws and crimpers. Failure to observe
this warning could result in injury or death.
CAutiOn
Wear eye protection. Metal chips can fly from blades
when cutting.
Do not cut short, free pieces of steel rods or ropes,
they may dangerously fly off; injury to the operator
and persons nearby may result.
Cutting CAPACitY:
- # 8 Copperweld.
- 4/0 Cu.
- 336 MCM Aluminium
- 477 MCM ACSR (Str. 26/7 )
OPERAtiOn:
1.
Install the cutting jaw in the tool (see the tool operation manual).
2.
Make sure the jaw is fully seated in the tool.
3.
Position the tool over the wire to be cut (for ACSR we strongly suggest to wrap wire with electrical
or duct tape around the area to be cut).
Advance the ram until the jaw comes in contact with the wire.
4.
Grip the tool firmly. Make sure that the cutting wire is supported so that it will not fall when the cut is
completed.
5.
Complete the cut, retract the ram, and remove the tool.
6.
Inspect the blades for cracks and make sure the jaw is seated properly before cutting again.
Do not attempt to sharpen or dress the cutting edge.
• Inspect the jaws before each use. Do not use damaged jaws.
• Damaged jaws can break and cause injury or damage to the tool.
• Work in a clean, uncluttered area.
• Keep persons away from immediate work area.
• Use this cutting jaws for the manufacturer’s intended purpose only.
WARning
Read and understand this instruction before using
this cutting jaws.
A person who has not read and does not understand
all operating instructions is not qualified to operate
these jaws. Failure to read and understand safety
instructions may result in injury or death.
Electrical Shock Hazard: The tool is not insulated and
the jaws will conduct electricity. This product should
be used only by persons knowledgeable in the safe
use of these jaws and crimpers. Failure to observe
this warning could result in injury or death.
CAutiOn
Wear eye protection. Metal chips can fly from blades
when cutting.
Do not cut short, free pieces of steel rods or ropes,
they may dangerously fly off; injury to the operator
and persons nearby may result.
Cutting CAPACitY:
- # 8 Copperweld.
- 4/0 Cu.
- 336 MCM Aluminium
- 477 MCM ACSR (Str. 26/7 )
OPERAtiOn:
1.
Install the cutting jaw in the tool (see the tool operation manual).
2.
Make sure the jaw is fully seated in the tool.
3.
Position the tool over the wire to be cut (for ACSR we strongly suggest to wrap wire with electrical
or duct tape around the area to be cut).
Advance the ram until the jaw comes in contact with the wire.
4.
Grip the tool firmly. Make sure that the cutting wire is supported so that it will not fall when the cut is
completed.
5.
Complete the cut, retract the ram, and remove the tool.
6.
Inspect the blades for cracks and make sure the jaw is seated properly before cutting again.
Do not attempt to sharpen or dress the cutting edge.
• Inspect the jaws before each use. Do not use damaged jaws.
• Damaged jaws can break and cause injury or damage to the tool.
• Work in a clean, uncluttered area.
• Keep persons away from immediate work area.
• Use this cutting jaws for the manufacturer’s intended purpose only.
