background image

25

CN-140 TECHNICAL MANUAL

03-2021

Translation of the original manual

14. START-UP SEQUENCE.

1. Install the machine completely fixed and stable.
2. Electrical connection of the unit. Ensure that the electrical connection is correct and

that the line is suitably shielded (magnetothermal and differential shielding).

3. Connect the machine to earth using the terminal fitted for the purpose (only necessary

in the event of the external power supply hose has no earth conductor).

4. Unroll the hoses.
5. Ensure that the emergency pushbutton is activated.
6. Connect product tanks to the machine by transfer pumps (they can be directly

connected to the machine in the event of emergency).

1

7. Connection of compressed air (external supply) to the distributor.
8. Open the main air valve located in the air distributor.
9. Adjust the pressure regulator to between 6 and 8 bars.
10. Unscrew the loose nut on each stopcock on the gun and insert the end of each hose into

their respective tanks (this task of recirculating liquids must be carried out before using
the machine for bleeding the air in the same).

2

11. Put the general switch in the ON position.
12. Connect the cylinder start button to fill the pumps with liquid.
13. Select the required temperature using the thermostat for each product and connect the

same with the start-up pushbutton.

3-4

14. Select the required temperature on the hose using the thermostat

5

.

15. As explained in point 10, these functions are performed without the gun for bleeding air

(leave the cylinder activated for a few minutes for effective bleeding).

16. Stop the machine to be able to perform the following procedures.
17. Reconnect both loose nuts on each product to the gun.
18. Open the air stopcock on the gun.
19. Open the air stopcock on both products on the gun.
20. The system is now ready to start the application

7

.

21. Use the appropriate means of personal protection

8

.

1

Do not start up the

system without material

in the pumps or tanks.

2.

Do not unscrew

the loose nut on the

gun with the

machine in

3

Do not connect the

heaters without

products.

4

The operational temperature will

vary depending on climatic

conditions or the reaction of the

different brands of the products.

5

Where necessary to alter the length of the hose, it

will be necessary to first alter the output voltage of

the transformer (Consult the Technical Assistance

service).

6

Do not open the taps on the

products without first opening

the air stopcock (on the gun).

7

Do not place any part of

the body in the direction of

the projection nor project

towards other people.

8

It is advisable to use protective goggles, air mask,

protective clothing and other safety equipment.

Manufacturers’ recommendations and the instructions

for the products used should be followed.

Summary of Contents for CN-140














































Reviews: