SureCall
TM
CM2000-WL 60dB
Dual Band SOHO Amplifier
User Manual
Model: CM2000-WL 60 dB
FCC ID: RSNDUAL-62UNDER
Canada IC: 7784A-D62UNDER
CONTENTS OF THE PACKAGE
fdgbsddg
1.
60dB amplifier
2.
5” patch Antenna with FME female connector
3.
110V AC Power Adaptor
4.
User Manual (this document)
5.
Velcro and Screw Mounting Kits
WHOLE PACKAGE OPTION:
fdgbsddg
Outdoor and indoor antenna as well as two pieces of CM240
cable are required for full operation. See picture below. Please
consult the Cellphone-Mate website or call toll free at 888-365-MATE.
1. CM2000-WL 60dB: 60dB Amplifier with Power Supply
2. CM004-20-FN: 20ft CM240 Cable
3. CM004-40-FN: 40ft CM240 Cable
4. CM222: Indoor Antenna
5. CM100-S: Outdoor Antenna
SAFETY NOTES
fdgbsddg
The Federal Communications Commission (FCC) who found it to
comply with their RF Exposure Requirements, Pursuant to FCC Part
22 and 24, has tested this product. In order to comply with the FCC
RF exposure requirements,
the human user’s body should
always be separated from the indoor antenna of the Amplifier
by at least 25cm (10”).
Don't expose this product to extreme high or low temperature. For
example, putting the Amplifier under direct sunshine for too long may
cause it to overheat, thereby damaging the electronic components
inside.
There are no consumer serviceable or modifiable parts inside this
Amplifier product. Alteration or abuse of the Amplifier or other
components will void this product’s warranty, and could be
dangerous to the user.
CONNECTING THE AMPLFIER
sddg
The signal is received by the outside antenna from the cell tower,
then AMPLIFIED and transmitted to your phone through the inside
antenna. When the phone transmits, the signal is received by the
inside antenna, then AMPLIFIED and transmitted to the cell tower
through the outside antenna.
Connect the Inside Antenna:
indoor dome antenna is always
recommended over the patch antenna. First, please mount dome
antenna on top of ceiling, and then please use the CM240 cable
connect dome antenna to the side of amplifier that marked
“INDOOR”, and make sure to tighten it.
If patch antenna is selected over dome antenna:
The patch
antenna is intended for indoors use only. Do not mount on a surface
within 4 inches of metal. Screw the patch antenna to the amplifier
connector that marked “
INDOOR
” and make sure to tighten it.
Connect the Outside Antenna:
The CM100-S fiber glass antenna
is for outdoor use only. Select an outside mounting location. For best
performance, try to keep the antenna on top of the house. The
outside antenna should be located in an area with at least a 12”
radius clear of obstructions, and other radiating elements. Use the
CM240 cable, connect the outside antenna in to the “
OUTDOOR”
connector of the amplifier and make sure to tighten it.
NOTE:
Keep the separation distance between the inside and outside
antennas at least 60 feet apart if possible.
WARNING:
The outside antenna must not be co-located or
operating in conjunction with any other antenna or amplifier.
Connect the Power Cord:
To prevent damage to the Amplifier,
before plugging in the Amplifier to an AC power outlet, make sure
the Amplifier’s power switch is in the OFF position. Then connect
the power cords to the Amplifier first, and then connect the plug to
110V AC power outlet. Make sure that all of the connections to the
Amplifier are tight and secure, and then turn on the Amplifier’s power
switch. The LED light will glow, indicating that the Amplifier is ready
to use.
Warning light: in the case that the red light turns
on, it means that the indoor and outdoor antennas
