16
17
ENGLISH
ENGLISH
PRECISIONCARE ALL DRIVE
PRECISIONCARE ALL DRIVE
Note:
The length of the cut may vary depending on the trimming angle. Begin with a
cut length dial for a longer cutting length and then use progressively shorter cutting
lengths as you cut hair.
Operating instructions
1.
Slide the power switch to the OFF position to turn OFF the device.
2.
Mount the comb attachment and adjust the length setting to match the desired
trimming length.
3.
Slide the power switch to the “ON” position to turn ON the device
4.
Trim against hair growth by guiding the flat comb part over the skin
5.
Avoid clogging the comb with hair by removing and periodically cleaning it.
Note:
The cut length dial will not turn when the device is switched ON.
5. CLEANING AND MAINTENANCE
•
Turn off and disconnect the device from the mains supply before cleaning,
maintaining it or assembling or disassembling any of its parts.
•
To clean the attachment, first remove it, brush it with the cleaning brush and
blow out hair clippings from the attachment and the main body of the device.
•
Remove the comb and blade attachments and rinse them under running water.
Do not use hot water.
•
Do not use compressed air, abrasive scouring pads, powders or cleaners to
clean the product.
•
Do not immerse the appliance’s body in water or any other liquid or place it
under running water.
•
Attachments are waterproof; therefore, they can be washed with water if
necessary. Dry them thoroughly before storing or using them again.
•
Clean the device and the attachments after each use with the cleaning brush.
Remove the attachment and rinse it under warm running water. Do not use
hot water.
Warning:
the body of the device is not washable. Do not submerge in water.
Oiling blades
•
Rinsing attachments under water (above) requires lubricating the cutting
blades once per month. Using only light-grade oils (e.g. sewing machine oil),
simply spread 1-2 drops lightly over cutters with the fingertip. Wipe away all
excess.
•
Use only light-grade oils as these will not evaporate nor slow down the speed
of the cutting blades.
•
Do not use hair oil, grease, or any oil mixed with kerosene nor solvent as these
too will evaporate.
6. TECHNICAL SPECIFICATIONS
Product name: PrecisionCare All Drive
Product reference: 04228
Voltage: 100-240 V~, 50/60 Hz
Made in China | Designed in Spain
7. DISPOSAL OF OLD ELECTRICAL APPLIANCES
The European directive 2012/19/EU on Waste Electrical and Electronic
Equipment (WEEE), specifies that old household electrical appliances must
not be disposed of with the normal unsorted municipal waste. Old
appliances must be collected separately, in order to optimize the recovery
and recycling of the materials they contain, and reduce the impact on human health
and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your obligation
to dispose of the appliance correctly. If the product has a built-in battery or uses
batteries, they should be removed from the appliance and disposed of appropriately.
Consumers must contact their local authorities or retailer for information concerning
the correct disposal of old appliances and/or their batteries.
8. GARANTÍA Y SAT
This product is under warranty for 2 years from the date of purchase, as long as the
proof of purchase is submitted, the product is in perfect physical condition, and it has
been given proper use, as explained in this instruction manual.
The warranty will not cover the following situations:
•
The product has been used for purposes other than those intended for
it, misused, beaten, exposed to moisture, immersed in liquid or corrosive
substances, as well as any other fault attributable to the customer.
•
The product has been disassembled, modified, or repaired by persons, not
authorised by the official Technical Support Service of Cecotec.
•
Faults deriving from the normal wear and tear of its parts, due to use.
•
The warranty service covers every manufacturing defects of your appliance
for 2 years, based on current legislation, except consumable parts. In the event
of misuse, the warranty will not apply.
If at any moment you detect any problem with your product or have any doubt, do not
hesitate to contact Cecotec Technical Support Service at
+34 96 321 07 28.
