F.o1t
=
3
-
Asymmetrical oscillator with start ON
This operating mode requires the setting of both
S.t1
and
S.t2
Set times.
Received the
Start
signal,
OUT1
is enabled for the
S.t1
time then disabled, reactivated at the end of
S.t2
time
and so on until the
Stop
/
Reset
.
S.t1
:
OUT1 ON time
,
S.t2
:
OUT1 OFF time
..
Reset
OUT1
Start
off
f.o1t
=
3
S.t1
S.t1
S.t2
S.t1
S.t2
F.o1t
=
4
-
Asymmetrical oscillator with start OFF
This operating mode implies the setting of both
S.t1
and
S.t2
Set times.
Received the
Start
signal,
OUT1
remains disabled for
the
S.t1
time then is activated for the time set at
S.t2
and
so on until the
Stop
/
Reset
.
S.t1
:
OUT1 OFF time
,
S.t2
:
OUT1 ON time
.
Reset
OUT1
Start
off
off
off
off
f.o1t
=
4
S.t2
S.t2
S.t1
S.t1
S.t1
F.o1t
=
5
-
Asymmetrical oscillator with start OFF 1 cycle
This operating mode operates as
f.o1t
=
4
but executes
only 1 Start/Pause
cycle.
Received the
Start
signal,
OUT1
remains disabled for
the
S.t1
time then is activated for the time set at
S.t2
.
The cycle can be repeated only after a
Reset
signal and
a new
Start
command.
Reset
OUT1
Start
off
off
S.t1
S.t2
f.o1t
=
5
5.4
OUT2 Operating mode
The Output 2 operation can be programmed in 5 different
modes with
F.o2t
parameter:
Se si desidera utilizzare
OUT2
è possibile stabilirne il funzi-
onamento tramite il parametro
F.o2t
secondo 5 diversi modi:
F.o2t
=
oF - OUT2 Output disabled
F.o2t
=
1
-
OUT2 works like OUT1
OUT2
output operates exactly like
OUT1
output in order
to have a double output contact.
F.o2t
=
2
-
OUT2 output works as an instant contact
(ON during count)
OUT2
is activated during the counting phase and re-
mains activated until the
Reset
command is received.
Reset
OUT1
f.o1t
=
1
Start
off
off
S.t1
OUT2
off
f.o2t
=
2
F.o2t
=
3
-
Out2 works as OUT1 (with
s.t1
time)
but with an absolute
s.T3
time
This operating mode requires the setting of
S.t1
and
S.t3
Set times.
S.t3
has the same time range and cannot be
longer than
S.t1
.
Received the
Start
command, instrument starts counting
and operates on
OUT2
output in the same mode it oper-
ates on
OUT1
(as
f.o1t
).
If
f.o1t
=
1
,
4
,
5
,
OUT2
operates as an
ON delay
func-
tion, when instead
f.o1t
=
2
,
3
OUT2
operates as a
Feed-through
function with
s.t3
Set time.
Reset
OUT1
Start
off
f.o1t
=
1
,
f.o2t
=
3
S.t1
OUT1
off
off
off
S.t3
Reset
OUT1
Start
off
f.o1t
=
2
,
f.o2t
=
3
S.t1
OUT2
off
S.t3
Reset
Start
f.o1t
=
3
,
f.o2t
=
3
OUT1
off
off
S.t1
S.t1
S.t2
OUT2
off
off
S.t3
S.t3
Reset
Start
f.o1t
=
4
,
f.o2t
=
3
OUT1
off
S.t2
S.t1
OUT2
off
off
off
off
off
S.t3
S.t2
S.t1
S.t3
ELETTROMECCANICA CDC S.r.l - TX40
- MANUAL rev.2 - PAG.
7
