CDA WF140 Installation, Use And Maintenance Manual Download Page 22

Page: 22 / 28

Fault Codes

The programme indicators also serve as a diagnostic display to help
in the event of a problem with the appliance.

Error code

Error

description

Advice

Wash

Rinse

Dry

End

Start/Pause

Inadequate

water supply

Make sure the water inlet tap is fully

open. Close the water tap, separate

the water inlet hose from the tap

and clean the filter. Restart your

machine and contact CDA service if

the error continues.

Continual fill

error

Close the tap and contact

CDA service.

The waste

water in the

machine

cannot be

discharged.

Drain hose is blocked.

The filters of your machine might

be blocked.

Restart the dishwasher and cancel

the programme. If the error

continues contact CDA service.

Heater error

Contact CDA service.

Alarm is active

against water

overflow

Turn off the dishwasher and

disconnect from the water supply.

Contact CDA service.

Faulty

electronic card

Contact CDA service.

Overheating

error

(temperature

in the machine

is too high.)

Contact CDA service.

Faulty heater

sensor

Contact CDA service.

Summary of Contents for WF140





























Search results

Summary of Contents for WF140

Reviews:

Related manuals for WF140

Brands by name

Popular brands

CDA WF140, Installation, Use And Maintenance Manual

Search results

Summary of Contents for WF140

Reviews:

Related manuals for WF140

Brands by name

Popular brands