CD3 Outpost Product Manual Download Page 46 | Manualshive

Page: 46 / 56

CD3 Outpost Product Manual Download Page 46

CD3 Products Manual

CD3, General Benefit Corporation |

www.cd3station.com

|

[email protected]

| 612.467.9441

Patent

Pending | Made in USA | © 2019

46

4.6.3 Compressor in Storage (Station/Wayside Only)

Before storing the compressor for a prolonged period, shut off the main power shut-off
switch. Remove all the pressure from the system.  For the station this includes pulling
the pressure relief valve to release all pressure from the receiver.  Drain all moistures
from the receiver.  Clean the filter housing:  replace the elements if necessary.  Drain
the oil from the compressor pump crankcase and replace it with new oil and run the unit
briefly.

4.6.2 Batteries in Storage (Wayside/Outpost Only)

Warning! - Do not leave the unit for any length of time with discharged batteries. The
batteries can discharge to the point where damage will occur and the battery charger
will not charge them.

To prepare the batteries for storage for a prolonged period of time (such as
winterization), make sure that the batteries are fully charged and then shut off the main
power shut-off switch. This prevents any phantom power drains on the system. The
batteries will continue to self-discharge over time so it is recommended that the unit is
charged if the duration of storage is longer than about 8 months. The main battery
disconnect must be turned back on to charge the unit. Make sure the unit is fully
charged again prior to use.

To fully charge the unit prior to disconnect:

Wayside 120V – Plug the unit in (or leave it plugged in if it is operated this way) without
using any of the functions and let stand until the green “100%” indicator illuminates –
see 3.7.1 Charging Procedure)

Wayside Solar/Outpost – Leave the unit with the solar panels in as much sun as possible
and discontinue use of the unit functions for a length of time to allow the batteries to
charge.  The status of batteries can be checked by opening the service door in the back
of the unit and finding the solar charge controller (shown below). The solar charger will
be straight inside the service door.  The indicated set of lights will display the battery
state of charge.

Outpost

Wayside Solar

«
...
44
45
46
47
48
...
»

Summary of Contents for Outpost

























































Reviews:

No comments