manualshive.com logo in svg

CD3 Outpost, Product Manual, Page: 45 / 56

Share
Download
CD3 Outpost Product Manual Download Page 45

CD3 Products Manual

 

CD3, General Benefit Corporation |  

www.cd3station.com

 |  

[email protected]

  

| 612.467.9441 

   

        

Patent 

Pending | Made in USA  | © 2019                                   

                                                                                                  

 

45 

4.

 

Re-torque the wheel lug nuts to 100 ft-lbs in an alternating crisscross pattern. 

 

4.6.2  Tire Pressure 

Under-inflation increases tire flexing and can result in tire failure.  Over-inflation causes a 
tire to be too stiff, making it more vulnerable to puncture from objects on the ground. 
Unequal tire pressure can cause instability.  All of these conditions can lead to uneven tire 
wear.  Take these steps to ensure correct tire pressures:  

a.

 

Use an accurate tire pressure gauge. 

b.

 

Check the tire pressure when tires are cold, which is after the trailer has been 
parked for over an hour or has been towed less than 2 miles.   

c.

 

Adjust the tire pressure according to the recommended specifications listed on 
the sidewall of the tires. 

 

4.6.3  Lift System Inspection 

The lift system should be visually inspected prior to any use to raise and lower the trailer 
body.  The inspection should look for anything that could infringe on the safe operation of 
the system.  Check for any frayed or misaligned cables or appearance of wear in any area 
not appropriate.  Excessive corrosion or damage to any component in the system could 
create a dangerous situation during use.

 

 

 

4.7  Storage/Winterization 

 

4.6.1  Cover 

A cover for the body of the unit is available from CD3 and is recommended for any long 
term storage duration (such as winterization) to protect the exterior finish of the unit.  
This helps to limit the exposure to the elements of the decals on the outside of the unit 
as well as contains the tools to minimize undesired tampering in the off season.  Unique 
covers are available for the Outpost, Station/Wayside, and Wayside Solar.  

The cover installs by placing it over the unit and zipping it closed to the base.  The base 
then has a ratcheting strap to pull the base tight.  The strap should be threaded through 
the ratchet, pulled tight and then tightened further with the ratchet.  The ratchet should 
be aligned under its cover flap and then covered by the flap. 

Summary of Contents for Outpost

























































Reviews:

No comments