CD Automation Revo C 3Ph 120A User Manual Download Page 26

Page: 26 / 70

REVO C

3PH from 60A to 210A

User’s manual

8.4 Schematic

NOTE:

The user installation must be protecting by electromagnetic circuit breaker or by fuse isolator.

The Fuse must be branch circuit protection. For UL any listed UL branch circuit fuse would be acceptable
as an external fuse, following national electric code guide for resistive heating of 125% load current rating
to protect external wires.

For SSR input connection follow next schematic.

IMPORTANT! Starting Strategy (Enable)

1: Feed the unit with L1-L2-L3 power voltage supply

2: Feed the auxiliary supply

3: Close the Enable contact to start with the regulation

MICRO

USB 2.0

Ethernet

Profibus

Function

Thermal

SC/HB

SLA

OUT

RETRANS. OUT

+24V

Fan Supply

230Vac Standard

115Vac Option

24Vdc Option

See Order Code

Option

Serial RS485

Second

Branch Circuit

Protection

Analog Inp.1

Analog SetPoint

Analog Inp.2

Reference

Ext.FeeDBack

Summary of Contents for Revo C 3Ph 120A







































































Search results

Summary of Contents for Revo C 3Ph 120A

Reviews:

CD Automation Revo C 3Ph 120A, User Manual, Page: 26 / 70

Search results

Summary of Contents for Revo C 3Ph 120A

Reviews: