Caviblaster 2040-D Operation & Maintenance Manual Download

Page: 5 / 38

2040-D O&M Manual Ver 3.0 CaviDyne



5077 Fruitville Rd.; Suite 109

– 157 Sarasota, FL 34234 U.S.A.



Phone 352.275 5319

Page 5/38

1.0 UNIT SPECIFICATIONS

The CaviBlaster

2040-D power unit consists of a 67HP (50 kW) Kubota V3600 diesel

power-pack and a CAT 3560 triplex plunger pump. Detailed performance and
specifications are listed below

CaviBlaster

2040-D Specifications

Nominal Pump Flow

20 GPM (76 LPM)

Nozzle Operating Pressure

3,700-PSI (255 BAR)

Engine

67 HP (50 kW), Diesel Powered (Kubota V3600)

Installation Environment

Outdoor enclosed or exposed

See Section 4 for installation requirements

Fuel Requirements

Diesel fuel (ASTM Grade No. 1-D or 2-D, or EN 590)

Fuel Tank Capacity

50 Gallons (190 Liters)

Water Inlet Pressure Limits

0-PSI (Atmospheric Pressure) to

70-PSI Maximum

(0 BAR to

4.8 BAR

)

See Section 4 for further requirements

Overall Unit Dimensions (L x W x H)

” x 55” x 62” (163 cm x 140 cm x 157 cm)

Maximum Pressure Hose Length

600 LF (200 meters)

of 3/4” diameter

Power Unit Weight (Dry)

2,400 LBS (1,100 KG)

Zero-Thrust Gun Weight

11 LBS (5 KG)

Figure 1.1

– CaviBlaster

2040-D Specifications

This space intentionally left blank

(EOS)

Summary of Contents for 2040-D







































Search results

Summary of Contents for 2040-D

Reviews:

Related manuals for 2040-D

Brands by name

Popular brands

Caviblaster 2040-D, Operation & Maintenance Manual

Search results

Summary of Contents for 2040-D

Reviews:

Related manuals for 2040-D

Brands by name

Popular brands