Casio Privia PX-S3100 User Manual Download Page 6

Page: 6 / 96

EN-5

Overview and Setup

Your Digital Piano uses an AC adaptor for power.

• Though this Digital Piano supports battery operation, use of

an AC adaptor is generally recommended.

■

Using the AC Adaptor

Make sure that you use only the AC adaptor specified for this
Digital Piano. Use of a different type AC adaptor can cause
smoking or malfunction.

• Never connect the AC adaptor (JEITA Standard, with

unified polarity plug) that comes with this Digital Piano
to any other device besides this Digital Piano. Doing so
creates the risk of malfunction.

• Be sure to turn off Digital Piano power before

connecting or disconnecting the AC adaptor.

• The AC adaptor will become warm to the touch after

very long use. This is normal and does not indicate
malfunction.

■

Using Batteries

• Be sure to turn off power before loading batteries.
• It is up to you to prepare six commercially available

alkaline batteries.

• Note the following precautions while the Digital Piano

is turned upside down to load batteries.

−

Take care to avoid injury due to pinching your
fingers under the Digital Piano.

−

Do not allow the Digital Piano to tip over or otherwise
be subjected to strong impact. Impact can damage
the volume knob and keyboard keys.

Open the battery cover on the bottom of the
Digital Piano.

Load six AA-size batteries into the battery
compartment.

Make sure the positive

and negative

ends of the

batteries are facing as marked on the Digital Piano.

Insert the tabs of the battery cover into the
holes on the side of the battery compartment,
and close the cover.

■

Low Battery and Replace Battery Notifications

A battery icon appears on the display to let you know when
battery power is getting low.

Low Battery Indicator

Replace Battery Indicator

• Using the Digital Piano while batteries are very low can

cause it to turn off suddenly. This can cause data
stored in Digital Piano memory to be corrupted or lost.

Preparing a Power Supply

Specified AC Adaptor: AD-A12150LW

(JEITA Standard plug)

Household power outlet

AC adaptor

DC 12V

Power cord

[

T O N E

]

P I A N O

T : 1 2 0

0 0 1 : G r P n o C o n c e r t

Low battery icon (not flashing)

[

T O N E

]

P I A N O

T : 1 2 0

0 0 1 : G r P n o C o n c e r t

Replace battery icon (flashing)

Summary of Contents for Privia PX-S3100

































































































Search results

Summary of Contents for Privia PX-S3100

Reviews:

Related manuals for Privia PX-S3100

Brands by name

Popular brands

Casio Privia PX-S3100, User Manual

Search results

Summary of Contents for Privia PX-S3100

Reviews:

Related manuals for Privia PX-S3100

Brands by name

Popular brands