Casio 5692 Operation Manual Download Page 5

Battery Replacement

Leave battery replacement up to your
original retailer or authorized CASIO
service center.

Have the battery replaced only with the type
specified in the “Specifications”. Use of a
different battery type can cause
malfunction.

When replacing the battery, also request a
check for proper water resistance.

Ornamental resin components may
become worn, cracked, or bent over time
when subjected to normal daily use. Note
that if cracking or any other abnormality
indicating possible damage is noticed in a
watch submitted for battery replacement,
your watch will be returned with an
explanation of the abnormality, without the
requested servicing being performed.

Initial Battery

The battery that comes loaded in your watch
when you purchase it is used for function
and performance testing at the factory.

The test battery may go dead quicker than
the normally rated battery life noted in the
“Specifications”. Note that you will be
charged for replacement of this battery,
even if replacement is required within your
watch’s warranty period.

Low Battery Power

Low battery power is indicated by large
timekeeping error, by dim display contents,
or by a blank display.

Operation while battery power is low can
result in malfunction. Replace the battery as
soon as possible.

Watch Operation Guide 5692

5

Summary of Contents for 5692



















Reviews: