manualshive.com logo in svg

Casio 3475, Operation Manual, Page: 8 / 58

Share
Download
Casio 3475 Operation Manual Download Page 8

●

Charging the Watch

Charger cable

USB

●

Align the down arrow (

) mark on the

watch with the up arrow mark (

) of the

connector.

1.

Turn on your computer or other device
with a USB port (power source), and
connect the charger cable to it.

2.

Connect the charger cable to the watch.

●

This starts charging and causes 

 to

flash on the watch display.

●

 disappears from the display when a

full charge is achieved.

●

Charging from a Non-computer
Device’s USB Port

You can charge using power from a USB port
(Type A) that meets the conditions below.

●

Voltage: 5 V

●

Current: 0.5 A min.

●

Precautions When Charging

●

Avoid charging while the battery level
indicator is showing 

. To obtain

longer chargeable battery life, charge only
when the battery level indicator is showing

 or lower.

●

Note that any of the conditions below can
hasten battery deterioration.

ー

Frequent charging while the battery is fully

or near fully charged

ー

Connecting and disconnecting the

charger cable multiple times during a
single day even though the battery is fully
charged

●

Do not attempt charging at high ambient
temperatures of 35°C or greater. The watch
becomes hot during charging, which can
cause charging to stop automatically. High
ambient temperature may result in a less
than full charge.

●

Operation on a custom computer or a
computer that has been modified from its
original configuration is not guaranteed.

●

Make sure that the charger cable connector
is oriented correctly when you plug it into the
watch.

●

The watch may become warm during
charging. This is normal and does not
indicate malfunction.

Note

●

Starting from a blank display, it takes
about 2.5 hours to achieve a full
charge.

●

Charging time depends on ambient
temperature and other factors.

Checking the Charge Level

You can check the watch’s current charge
level in all modes, except those below.

●

Training Log Mode

●

Training Status Mode

●

Notification Mode

Level

Indicator Usable Functions

HIGH

All

MID

LOW

All functions except
those that use GPS
All functions except
those that use GPS,
HR (heart rate)

CHG

●

Normally (not charging):
Blank display

●

During USB charging
(charging in progress):
[CHARGING BATTERY] only
displayed

●

The display goes blank when the battery
goes dead.

Important!

●

Charge the watch as soon as possible
after the battery indicator becomes

 or lower. Leaving the watch

without charging for a number of
months will result in over-discharge,
and may make future charging
impossible. If this happens, contact
your original retailer.

●

If the battery is dead and the watch
display is blank, use the charger cable
to charge the watch.

Operation Guide 3475

8

Summary of Contents for 3475



























































Reviews:

No comments