Casio 3461 User'S Operation Manual Download Page 2

Before Getting

Started...

This section provides an overview of the watch
and introduces convenient ways it can be
used.

Note

The illustrations included in this
operation guide have been created to
facilitate explanation. An illustration
may differ somewhat from the item it
represents.

Indicators

① ②

A

Displayed while Power Saving is enabled.

B

Displayed while Auto Light is enabled.

C

Displayed after time adjustment using

time signal reception or connection with a

phone was successful.

The [RCVD] indicator will disappear in

the cases below.

After you use watch operations to

change Home City settings (time and

date, city, summer time)

After the watch switches between

standard time and summer time

After a time signal receive operation

fails

After a phone-based time adjustment

operation fails

D

Displayed while there is connection

between the watch and a phone.

E

Displayed during p.m. times while 12-hour

timekeeping is being used.

F

Displayed while the watch is indicating

summer time.

G

Displayed while battery power is low

H

Displayed while an alarm is turned on.

I

Displayed while the hourly time signal is

enabled.

J

Displayed while the operation tone is

muted.

K

Displayed while the snooze alarm is

enabled.

Navigating Between Modes

Press (C) to cycle between modes.

In any mode, hold down (C) for about one

second to enter the Timekeeping Mode.

C

C

C

C

C

World Time Mode

Alarm Mode

Timer Mode

Stopwatch Mode

Timekeeping Mode

Connecting with a Phone

Hold down (C) for about three seconds to

establish a connection with a phone.

To disconnect, press any button.

C

After connection

Before connection

Any button

Solar Charging

This watch runs on power supplied from a
rechargeable (secondary) battery that is
charged by a solar panel. The solar panel is
integrated into the face of the watch, and
power is generated whenever the face is
exposed to light.

Charging the Watch

When you are not wearing the watch, put it in
a location where it is exposed to bright light.

While you are wearing the watch, make sure
that its face (solar panel) is not blocked from
the light by the sleeve of your clothing. Power
generation efficiency is reduced even when
the face of the watch is blocked only partially.

NO

YES

Important!

Depending on light intensity and local
conditions, the watch may become hot
to the touch when exposed to light for
charging. Take care to avoid burn
injury after charging. Also, avoid
charging the watch under high-
temperature conditions like the ones
described below.

On the dashboard of a vehicle

parked in the sun

Near an incandescent light bulb or

other source of heat

Under direct sunlight or in other hot

areas for long periods

Operation Guide 3459/3461

2

Summary of Contents for 3461























Reviews: