1 - GENERAL INFORMATION
1 - GENERAL INFORMATION
###_1_###
Note to the Owner
Improper operation of this machine can cause injury or death. Before using this machine, make certain that every
operator:
• Is instructed in safe and proper use of the machine.
• Reads and understands the Manual(s) pertaining to the machine.
• Reads and understands ALL Safety Decals on the machine.
• Clears the area of other persons.
• Learns and practices safe use of machine controls in a safe, clear area before operating this machine on a job site.
It is your responsibility to observe pertinent laws and regulations and follow CASE CONSTRUCTION instructions on
machine operation and maintenance.
Your machine has been designed and built to the highest standards of quality. It conforms to all current safety reg-
ulations. However, the risk of accidents can never be completely excluded. That is why it is essential to observe
elementary safety rules and precautions.
Read this manual carefully, paying particular attention to the instructions concerning safety, operation and mainte-
nance so as to avoid the risk of injury while operating or servicing the machine.
The standard attachments and tools of this machine are designed to carry out all kinds of earthmoving and rehan-
dling operations. If you want to use this machine to handle a load (pipes, culverts, formwork, etc.), make sure that
it is designed to carry out this kind of work. For this type of application, the machine must be equipped with safety
valves, a load handling chart corresponding to the type of machine and its attachment and a load fixing point. All legal
requirements must also be strictly observed.
Do not use this machine for any application or purpose other than those described in this manual. If the machine is
to be used for work involving the use of special attachments, accessories or equipment, consult your CASE CON-
STRUCTION Dealer in order to make sure that any adaptations or modifications made are in keeping with the ma-
chine's technical specifications and with prevailing safety requirements.
Any modification or adaptation which is not approved by the manufacturer may invalidate the machine's initial confor-
mity with safety requirements.
The machine must undergo regular inspections, the frequency of which varies according to the type of use. Consult
your CASE CONSTRUCTION Dealer.
ATTENTION:
The engine and fuel system on your machine is designed and built to government emissions standards.
Tampering by dealers, customers, operators and users is STRICTLY PROHIBITED BY LAW. Failure to comply could
result in government fines, rework charges, invalid warranty, legal action and possible confiscation of the machine
until rework to original condition is completed. Engine service and/or repairs must be done by a certified technician
only.
Your CASE CONSTRUCTION Dealer is at your disposal for any further information. He will also provide any after-
sales service you may require, and genuine CASE CONSTRUCTION spare parts, your guarantee of quality and
match. CASE CONSTRUCTION customer assistance is also available. Call 1-866-54-CASE6 (1-866-542-2736) or
email [email protected].
You can obtain manuals on the operation, maintenance and repair of your machine from your CASE CONSTRUCTION
Dealer. To ensure quick and efficient service, consult your CASE CONSTRUCTION Dealer for assistance in ordering
the correct manuals for your machine.
Your CASE CONSTRUCTION Dealer can provide after-sales service and genuine CASE CONSTRUCTION spare
parts, your guarantee of quality and match.
CNH Industrial America LLC. Company reserves the right to make changes in the specification and design of the
machine without prior notice and without incurring any obligation to modify units previously sold.
1-1
Summary of Contents for CX490D
