manualshive.com logo in svg

Case 721G Stage IV, Operator'S Manual

Share
Download
Case 721G Stage IV Operator'S Manual Download Page 386

7 - MAINTENANCE

Urea Quality Sensor (UQS) - Replace

CAUTION

Flying debris!
Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using com-
pressed air.
Failure to comply could result in minor or moderate injury.

C0049A

Prior operation:

Keep all non-authorized personnel clear of the area. Park the machine on a firm, level surface in neutral with the
parking brake applied. Lower the bucket/attachment to the ground. Turn off the engine. Install the transport/service
link into the locked position.

1. Turn the timed disconnect switch to the OFF position.

RCPH11WHL653BAU

1

2. Remove the access cover below the

DEF/A

D

B

LUE

®

tank to gain access to the Urea Quality Sensor (UQS).

NOTE:

use compressed air and water to clean debris from

around drain plug area.

NOTE:

the urea quality sensor on the bottom of the DEF/

ADBLUE® tank can be removed to drain fluid as neces-
sary. When removing the urea quality sensor, it is rec-
ommended that the electrical harness should not be dis-
connected from the urea quality sensor. The urea quality
sensor should be cleaned by flushing with deionized water
before re-installation. Note that the sensor should not be
submerged while cleaning so that water does not enter the
vent located on the bottom of the sensor. Also note that if
the harness was disconnected from the sensor, the elec-
trical pins must be cleaned with electrical contact cleaner
and dried before the harness is reconnected to the sensor.

LEIL17WHL1583AB

2

7-148

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands