Home
/
Case
/
721G Stage IV
/
Operator'S Manual

Case 721G Stage IV, Operator'S Manual

Share

Page: 359 / 522

Case 721G Stage IV Operator'S Manual Download Page 359

7 - MAINTENANCE

Transmission oil filter - Replace

WARNING

Chemical hazard!
When handling fuel, lubricants, and other service chemicals, follow the manufacturer's instructions.
Wear Personal Protective Equipment (PPE) as instructed. Do not smoke or use open flame. Collect
fluids in proper containers. Obey all local and environmental regulations when disposing of chemi-
cals.
Failure to comply could result in death or serious injury.

W0371A

WARNING

Pressurized fluid can penetrate the skin and cause severe injuries.
Keep hands and body away from any pressurized leak. DO NOT use your hand to check for leaks. Use
a piece of cardboard or paper. If fluid penetrates the skin, seek medical attention immediately.
Failure to comply could result in death or serious injury.

W0158A

Replace the transmission oil filter every 1500 hours or more frequently when operating conditions are severe.
Shorten the service intervals in severe applications which involve running the torque converter under high load for
more than 25% of operation time. Applications include basement digging or land clearing.

Prior operation:

Keep all non-authorized personnel clear of the area. Park the machine on a firm, level surface in neutral with the
parking brake applied. Lower the bucket/attachment to the ground. Turn off the engine. Install the transport/service
link into the locked position.

NOTE:

it is recommended to change the transmission oil when you replace the engine oil filter.

1. If present on the machine remove the right-hand steps

(1)

and chassis side cover

(2)

to access the transmis-

sion oil filter.

NOTE:

remove the right-hand steps

(1)

only if necessary.

LEIL17WHL1580AB

1

2. Clean the area around the transmission oil filter head.

3. Remove the transmission oil filter.

4. Apply a film of clean

CASE AKCELA NEXPLORE™

FLUID

to the gasket of the new filter and install. Make

sure that the proper contact is made with the base.

5. Clean the transmission breather and reinstall. See the

transmission breather cleaning procedure. Refill with
clean

CASE AKCELA NEXPLORE™ FLUID

.

6. Check the oil level at the sight gauge.

7. Start the engine and check for oil leaks around the filter

and drain plug.

8. Bring the transmission oil up to working temperature,

and check the level again.

RCPH10WHL127AAH

2

7-121

«
...
357
358
359
360
361
...
»

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands