manualshive.com logo in svg

Case 721G Stage IV, Operator'S Manual

Share
Download
Case 721G Stage IV Operator'S Manual Download Page 342

7 - MAINTENANCE

Every 1000 hours

Pivot points - Grease

WARNING

Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.

W0047A

Grease the fittings of the upper and lower chassis pivot points every 1000 hours or sooner if conditions so require.

Prior operation:

Keep all non-authorized personnel clear of the area. Park the machine on level ground, in neutral with the parking
brake applied and the attachment lowered to the ground.

Service specifications

Grease

CASE AKCELA MOLY GREASE

NOTE:

if the machine is equipped with automatic lubrication system, you do not need to perform following instructions.

LEIL18WHL1154FA

1

7-104

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands