manualshive.com logo in svg

Case 721G Stage IV, Operator'S Manual

Share
Download
Case 721G Stage IV Operator'S Manual Download Page 209

5 - TRANSPORT OPERATIONS

5 - TRANSPORT OPERATIONS

###_5_###

Recovery transport

Safety rules

WARNING

Crushing hazard!
Engage the safety lock link before service or transport.
Failure to comply could result in death or serious injury.

W1154A

WARNING

Driving hazard!
Know all rules, regulations, laws, and required safety equipment for transporting or operating this ma-
chine on a road or highway. See your dealer to obtain a rotating beacon, backup alarm, Slow Moving
Vehicle (SMV) emblem, and other safety equipment.
Failure to comply could result in death or serious injury.

W0154A

WARNING

Transport hazard!
The machine can slip or fall from a ramp or trailer. Make sure the ramp and trailer are not slippery.
Remove all oil, grease, ice, etc. Move the machine on or off the trailer with machine centered on the
trailer or ramp.
Failure to comply could result in death or serious injury.

W0152A

WARNING

Transport hazard!
Always use the primary steering when loading or unloading the machine for transport. Do not use
joystick steering when loading or unloading the machine from a truck or trailer.
Failure to comply could result in death or serious injury.

W0448A

Make sure you know the safety rules and regulations be-
fore transporting the machine. You must know the rules
or laws for transportation and safety that are used in each

area that you will be in. Make sure that the truck and ma-
chine are equipped with the correct safety equipment.

5-1

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands