manualshive.com logo in svg

Case 721G Stage IV, Operator'S Manual

Share
Download
Case 721G Stage IV Operator'S Manual Download Page 175

4 - OPERATING INSTRUCTIONS

4 - OPERATING INSTRUCTIONS

###_4_###

Commissioning the unit

Before starting the engine

WARNING

IMPROPER OPERATION OF THIS MACHINE CAN CAUSE DEATH OR SERIOUS INJURY.
MAKE SURE THAT EVERY OPERATOR:
-is instructed in the safe and proper use of this machine.
-reads and understands the operator's manual for this machine.
-reads and understands ALL safety signs on the machine.
Failure to comply could result in death or serious injury.

W0188A

WARNING

Avoid injury!
Do not operate the machine while under the influence of alcohol or drugs.
Failure to comply could result in death or serious injury.

W0160A

Before starting the engine

1. Perform a daily walk around and visual inspection

of the machine. Check for loose connections, faulty
hoses, oil leaks, debris or trash buildup, loose bolts,
damaged, or missing parts that could affect the nor-
mal and safe operation of the machine. Make any
necessary corrections before operating the machine.

2. See the quick reference “Maintenance Chart” – Chap-

ter 7 in this manual and complete the items in the daily
- 10 hours section of the chart.

3. Check that the machine fuel tank is filled with clean

fuel that matches the specifications given in “General
specification - Diesel fuel" – Chapter 7 in this manual.

4. Check and make certain the

DEF/A

D

B

LUE

®

tank is

properly filled. Low volume in the tank can cause loss
of power and torque. Fill the

DEF/A

D

B

LUE

®

tank after

approximately 1.5 fuel fills. Do not allow the

DEF/

A

D

B

LUE

®

tank to drop below

10%

volume for the best

engine performance.

The machine will last longer, give better and more
economical performance, if you pay particular attention
to the engine and carry out the following checks:

• Warm up the engine before using it under load.

• Do not operate the engine at maximum power for pro-

longed periods of time.

• Do not run the engine for a long period at idle speed.

• Check the indicators on the multifunction display fre-

quently.

• Check the oil levels and coolant level frequently.

4-1

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands