manualshive.com logo in svg

Case 721G Stage IV, Operator'S Manual

Share
Download
Case 721G Stage IV Operator'S Manual Download Page 119

3 - CONTROLS AND INSTRUMENTS

Parking brake

WARNING

Run-over hazard!
Apply the parking brake before leaving the cab.
Failure to comply could result in death or serious injury.

W1390A

Parking brake button

Make sure the machine has come to a
complete stop before applying the parking
brake.

The parking brake button engages the parking brake on
the transmission output shaft.

NOTICE:

the parking brake is a spring applied, hydraulic

released brake which is applied to the drive shaft. The
parking brake will effectively hold the machine in place
when used correctly.

LEIL16WHL1125AA

1

Engaging the parking brake

To engage the parking brake, move the transmission con-
trol lever to NEUTRAL (N), stop the machine and push
the parking brake button. The parking brake will automat-
ically engage when the machine is shut off.

NOTICE:

a failure in the operating procedure or a failure

in the electrical or hydraulic function can result in abrupt
engagement of the parking brake. Always wear your seat
belt.

NOTICE:

apply the parking brake prior to leaving the cab

and/or parking the machine on slopes.

Parking brake release

NOTE:

the service brake must be at operating pressure

before the parking brake can be released to move the ma-
chine. The brake pressure indicator lamp on multifunc-
tion display must not be illuminated when disengaging the
parking brake. Attempting to move the machine prior to
the service brake pressures being sufficient causing low
operating pressure can result in premature parking brake
pad wear.

LEIL16WHL1570AB

2

3-35

Summary of Contents for 721G Stage IV











































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands