manualshive.com logo in svg

Case 570NXT, Service Manual

The Case 570NXT Service Manual is a comprehensive user manual designed to assist users in understanding and maintaining the 570NXT model. Available for free download from manualshive.com, this manual provides detailed instructions, diagrams, and troubleshooting tips, enhancing the overall user experience and optimizing machine performance.

Share
Download
background image

Engine - Engine and crankcase

Engine - General specification

Model

Diesel, F5HFL413D*A

Type

Four cylinder, turbocharged

Firing order

1 - 3 - 4 - 2

Bore and stroke

99mm x 110mm (3.9 in x 4.33 in)

Displacement

3.4 l

(

207 in³

)

Compression ratio

16.5 to 1

Fuel injection

Direct HPCR

Horsepower - rated at

2200 RPM

Gross
Net with 39° fan

63 kW

(

85 Hp

)

58 kW

(

79 Hp

)

Peak torque at

1400 RPM

Gross
Net with 39° fan
Maximum torque rise

374 N·m

(

276 lb ft

)

364 N·m

(

268 lb ft

)

36% ±

5 RPM

Engine - Speeds stall test check sheet

Results from stall test procedure (fill in values accordingly)

ID

RPM test valve

Stall test component (specified value)

1

Loader hydraulic stall speed (

2200 - 2330 RPM

)

2

Torque converter stall speed (

2150 - 2310 RPM

)

3

Combined - loader hydraulic and torque converter - stall speed (

1610 - 1890 RPM

)

Stall test reference chart

ID

RPM

Results

1

2230 to 2330

2

2180 to 2310

3

1610 to 1890

All systems operating within normal specified RPM values.

1

Above 2330

2

Above 2310

3

Above 1890

Engine problem. Check engine speeds. Refer to the engine service manual.

1

Below 2230

2

Below 2180

3

Below 1610

Engine problem. Check engine speeds. Replace the fuel and air filters. Refer
to the engine service manual.

1

Below 2230

2

2180 to 2310

3

Below 1610

Hydraulic system problem(s). Check the setting of the main relief valve. Check the
output of the hydraulic pump.

1

Above 2330

2

2180 to 2310

3

Above 1890

Hydraulic system problem(s). Check the setting of the main relief valve. Check the
output of the hydraulic pump. Check for leakage in the loader control valve.

1

2230 to 2330

2

2180 to 2310

3

1610 to 1890

Hydraulic system problem(s). Check the setting of the main relief valve. Check the
output of the hydraulic pump.

1

2230 to 2330

2

2180 to 2310

3

1610 to 1890

Hydraulic system problem(s). Check the setting of the main relief valve. Check the
output of the hydraulic pump.

1

2230 to 2330

2

Above 2310

3

Above 1890

Torque converter or transmission problems.

1

2230 to 2330

2

Below 2180

3

Below 1610

Torque converter or transmission problems.

47441594 27/09/2012

10.001 / 3

Summary of Contents for 570NXT




















































Reviews:

No comments

Related manuals for 570NXT

jcb 525-60 Operator'S Manual preview
525-60
Brand: jcb Pages: 31
jcb 6T-1 Front Tip Service Manual preview
6T-1 Front Tip
Brand: jcb Pages: 51
AVANT 744i Operator'S Manual preview
744i
Brand: AVANT Pages: 146
AEM 418-12 Operator'S Manual preview
418-12
Brand: AEM Pages: 528
Gehl ,5625DX Operator'S Manual preview
,5625DX
Brand: Gehl Pages: 92
Gehl SL3640E Operator'S Manual preview
SL3640E
Brand: Gehl Pages: 88
Gehl 418T Wheel Operator'S Manual preview
418T Wheel
Brand: Gehl Pages: 192

Brands by name

Popular brands

Load more brands