Case 48083741 Service Manual Download Page 40 | Manualshive

Page: 40 / 61

background image

Engine - Engine and crankcase

Engine - Remove

1. Park the machine on a level surface and lower the

bucket to the ground.

Put the articulation lock in

LOCKED position and stop the engine.

LEIL16WHL0048AB

1

2. Actuate the brake pedal several times to discharge the

brake accumulators.

LEIL15WHL0564AA

2

3. Put the key switch to ON position.

Press the hydraulic functions lock-out button to unlock
all hydraulic functions.
Move the control lever(s) back and forth at least 30
times to release any pressure from the hydraulic circuit.
Put the key switch to OFF position.

LEIL16WHL1286AA

3

4. Raise the grill located above the cooler box just behind

the cab. Then slowly loosen the hydraulic reservoir
filler cap to release pressure in the reservoir.

LEIL17WHL0028AB

4

48083741_EN 31/07/2018

10.1 [10.001] / 5

«
...
38
39
40
41
42
...
»

Summary of Contents for 48083741






























































Reviews:

No comments

Related manuals for 48083741

SWL 2021 Series

Brand: SUNWARD Pages: 91

Brand: SUNWARD Pages: 78

Brand: MX Pages: 28

Brand: MX Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands