Case IH Farmall 105U Pro EP Service Manual Download

Page: 378 / 1569

Front axle system - Final drive hub, steering knuckles, and shafts

Planetary drive and hub - Disassemble

Front epicyclic final drive with brake

NOTE:

Front epicyclic final drive removal and installation can be carried out with the axle detached and positioned

on the stand

380000251

, or with the axle fitted on the tractor. If the operation is performed with the axle fitted on the

tractor, a support stand must be positioned under the engine sump.

1. Position the axle on stand

380000251

2. Remove the plug

(1)

and drain the oil from the epicyclic

final drive.

SEZ25CAP1A-59

3. Unscrew all of the epicyclic final drive casing retaining

bolts

(1)

SEZ25CAP1A-60

4. Using an extractor

(1)

, fitted on the oil drainage plug,

detach the epicyclic final drive casing

(2)

SEZ25CAP1A-61

47735452 03/07/2014

25.3 [25.108] / 9

Summary of Contents for Farmall 105U Pro EP


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Farmall 105U Pro EP

Reviews:

Related manuals for Farmall 105U Pro EP

Brands by name

Popular brands

Case IH Farmall 105U Pro EP, Service Manual

Search results

Summary of Contents for Farmall 105U Pro EP

Reviews:

Related manuals for Farmall 105U Pro EP

Brands by name

Popular brands