M6027 • 01/13/17 • © 2017 Casablanca Fan Company
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with RSS-210 of Industry Canada. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: Reorient
or relocate the receiving antenna, Increase the separation between the
equipment and receiver, Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. Consult the dealer
or an experienced radio/TV technician for help. Note: Any changes or
modifications to the transmitter or receiver not expressly approved by
Hunter Fan Company may void one’s authority to operate this remote
control.
This product conforms to UL Standard 1917.
WARNINGS
CEILING FAN REMOTE WALL CONTROL
Model 99195
CASABLANCA FAN COMPANY CONTROL LIMITED WARRANTY
This product is warranted to the original purchaser by Casablanca
Fan Company against defects in material and workmanship for
one (1) year from date of purchase. During the warranty period,
we will repair or, at our option, replace a defective product at
no charge. For information on how to obtain service, contact
Casablanca’s Service Department by calling our toll-free number
at 1-888-227-2178. Damage to the product caused by mishandling,
improper installation or modification is not covered by this
warranty. This warranty is given in lieu of all other warranties
expressed or implied. Some states do not allow limitations of time
on an implied warranty, therefore the above limitations may not
apply in every case. This warranty states specific legal rights which
may vary from state to state.
2
4
Installing the battery
Wiring the Wall Control
INSTALLATION
Before installation, use the pull chains to set
the fan speed to HIGH and the light to ON.
Ensure the power is OFF at the outlet box and
wall switch location before proceeding with
installation.
Turn
Pow
er
OFF
1
Turning off the power
To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by
turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot
lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a
tag, to the service panel.
To access the battery compartment, slide the
battery door up.
Replace the used battery with two AAA batteries
when needed.
Battery
Door
READ AND SAVE THESE INSTRUCTIONS
If you are installing multiple remote-controlled fans
on the same circuit breaker
,
you may need to perform a few extra steps to prevent interference or faulty
operation of your remote controls.
Go to www.CasablancaFanCo.com/FAQs and click “How do I properly install multiple
remote-controlled fans?” for more information.
1.
Connect the grounding wire from
the wall control to the ground
control from the switch box using
the provided wire nuts.
2.
Connect the “LIVE IN” from the
switch box to the “~VAC” from the
wall control using the provided
wire nuts.
3.
Connect the “LIVE OUT” from the
switch box to the “FAN” out from
the wall control using the provided
wire nuts.
4.
Push all wires into the switch box.
3
Installing the Wall Plate Bracket
Snap the Wall Control into the Wall
Plate Bracket. Ensure that the lip on
the bracket is facing outward.
