CAS NT-500 Series Page 59 Owner'S Manual Download

Page: 59 / 66

15. Error Messages & Troubleshooting

(1) Weighing mode

CH 01

▣

Reason

Internal RAM is erased.

☞

Troubleshooting

Please call your CAS dealer.

CH 02

▣

Reason

Load cell connection failure or error in A/D conversion part.

☞

Troubleshooting

Please call your CAS dealer.

CH 03

▣

Reason

The zero range exceeds

10% of maximum capacity.

☞

Troubleshooting

Check that there is nothing on the platform.

CH 04

▣

Reason

You pressed any key for long time or there is a problem in key part.

☞

Trouble-shooting

If there is no problem in key part, call your CAS dealer.

CH 05

▣

Reason

Failure of print connection.

☞

Troubleshooting

Check the connection between NT-505A & Printer.

Over

▣

Reason

The display weight is greater than the maximum capacity that you have set.

☞

Troubleshooting

The weight of item is greater than the max. capacity on the platform.
This may damage Load Cell.

Summary of Contents for NT-500 Series



































































Search results

Summary of Contents for NT-500 Series

Reviews:

Related manuals for NT-500 Series

Brands by name

Popular brands

CAS NT-500 Series, Owner'S Manual

Search results

Summary of Contents for NT-500 Series

Reviews:

Related manuals for NT-500 Series

Brands by name

Popular brands