SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com E-Mail: [email protected]
2) Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary: Press and hold -> On; Release -> Off.
Press and hold button A: Terminals OUT1 outputs DC power, the lamp 1 is on. Release button A: Terminals OUT1 stops outputting, the lamp 1 is
off.
……
Press and hold button D: Terminals OUT4 outputs DC power, the lamp 4 is on. Release button D: Terminals OUT4 stops outputting, the lamp 4 is
off.
3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Control mode Latched: Press -> On, Press another button -> Off.
Press button A: Terminals OUT1 outputs DC power, the lamp 1 is on, other 3 lamps are off.
Press button B: Terminals OUT2 outputs DC power, the lamp 2 is on, other 3 lamps are off.
Press button C: Terminals OUT3 outputs DC power, the lamp 3 is on, other 3 lamps are off.
Press button D: Terminals OUT4 outputs DC power, the lamp 4 is on, other 3 lamps are off.
4)
Setting control mode Momentary (Channel 1~2) + Toggle (Channel 3~4): Connect Jumper-1 and Jumper-2.
Press and hold button A: Terminals OUT1 outputs DC power, the lamp 1 is on. Release button A: Terminals OUT1 stops outputting, the lamp 1 is
off.
Press and hold button B: Terminals OUT2 outputs DC power, the lamp 2 is on. Release button B: Terminals OUT2 stops outputting, the lamp 2 is
off.
Press button C: Terminals OUT3 outputs DC power, the lamp 3 is on. Press button C again: Terminals OUT3 stops outputting, the lamp 3 is off.
Press button D: Terminals OUT4 outputs DC power, the lamp 4 is on. Press button D again: Terminals OUT4 stops outputting, the lamp 4 is off.
Wired control terminals:
The receiver has wired control terminals, you can connect external devices, sensors, or manual switches to control the receiver.
1) The manual switches:
You can connect manual switches to terminals
“Signal-”, “Signal 1+”, “Signal 2+”, “Signal 3+”, “Signal 4+”, then you can use the manual switches
to control the receiver.
When connect terminals
“Signal 1+” and “Signal-”, Terminals OUT1 outputs DC power, the lamp 1 is on. And when disconnect “Signal 1+” and
“Signal-”, Terminals OUT1 stops outputting, the lamp 1 is off.
When connect terminals
“Signal 2+” and “Signal-”, Terminals OUT2 outputs DC power, the lamp 2 is on. And when disconnect “Signal 2+” and
“Signal-”, Terminals OUT2 stops outputting, the lamp 2 is off.
When connect terminals
“Signal 3+” and “Signal-”, Terminals OUT3 outputs DC power, the lamp 3 is on. And when disconnect “Signal 3+” and
“Signal-”, Terminals OUT3 stops outputting, the lamp 3 is off.
When connect terminals
“Signal 4+” and “Signal-”, Terminals OUT4 outputs DC power, the lamp 4 is on. And when disconnect “Signal 4+” and
“Signal-”, Terminals OUT4 stops outputting, the lamp 4 is off.
2) Signal input:
You can connect external devices (with low level output signal) to terminals
“Signal-”, “Signal 1+”, “Signal 2+”, “Signal 3+”, “Signal 4+”, then the
external device
’s output signal can control the receiver.
When the external device outputs low level signal to terminal
“Signal –” and terminal “Signal 1+”, Terminals OUT1 outputs DC power, the lamp 1
is on. When t
he
external
device
stops
to output
signal, Terminals OUT1 stops outputting, the lamp 1 is off.
When the external device outputs low level signal to terminal
“Signal –” and terminal “Signal 2+”, Terminals OUT2 outputs DC power, the lamp 2
is on. When t
he
external
device
stops
to output
signal, Terminals OUT2 stops outputting, the lamp 2 is off.
When the external device outputs low level signal to terminal
“Signal –” and terminal “Signal 3+”, Terminals OUT3 outputs DC power, the lamp 3
is on. When t
he
external
device
stops
to output
signal, Terminals OUT3 stops outputting, the lamp 3 is off.
When the external device outputs low level signal to terminal
“Signal –” and terminal “Signal 4+”, Terminals OUT4 outputs DC power, the lamp 4
is on. When t
he
external
device
stops
to output
signal, Terminals OUT4 stops outputting, the lamp 4 is off.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.
2) Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
Delete all transmitters:
We have learned remote control to
the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.